ATtiny24A Atmel Corporation, ATtiny24A Datasheet - Page 48

• Manufacturer Part Number: ATtiny24A
• Manufacturer: Atmel Corporation

Specifications of ATtiny24A

• Flash (kbytes): 2 Kbytes
• Pin Count: 14
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 12
• Ext Interrupts: 12
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

9.2
9.2.1
48
External Interrupts
ATtiny24A/44A/84A
Low Level Interrupt
External Interrupts are triggered by the INT0 pin or any of the PCINT[11:0] pins. Observe that, if
enabled, the interrupts will trigger even if the INT0 or PCINT[11:0] pins are configured as out-
puts. This feature provides a way of generating a software interrupt. Pin change 0 interrupts
PCI0 will trigger if any enabled PCINT[7:0] pin toggles. Pin change 1 interrupts PCI1 will trigger
if any enabled PCINT[11:8] pin toggles. The PCMSK0 and PCMSK1 Registers control which
pins contribute to the pin change interrupts. Pin change interrupts on PCINT[11:0] are detected
asynchronously, which means that these interrupts can be used for waking the part also from
sleep modes other than Idle mode.
The INT0 interrupt can be triggered by a falling or rising edge or a low level. This is set up as
shown in
and configured as level triggered, the interrupt will trigger as long as the pin is held low. Note
that recognition of falling or rising edge interrupts on INT0 requires the presence of an I/O clock,
as described in
A low level interrupt on INT0 is detected asynchronously. This means that the interrupt source
can be used for waking the part also from sleep modes other than Idle (the I/O clock is halted in
all sleep modes except Idle).
Address Labels Code
0x0000
0x0001
0x0002
0x0003
0x0004
0x0005
0x0006
0x0007
0x0008
0x0009
0x000A
0x000B
0x000C
0x000D
0x000E
0x000F
0x0010
;
0x0011
0x0012
0x0013
0x0014
0x0015
0x0016
...
“MCUCR – MCU Control Register” on page
RESET: ldi
“Clock Sources” on page
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
out
ldi
out
sei
<instr>
...
RESET
INT0
PCINT0
PCINT1
WDT
TIM1_CAPT
TIM1_COMPA
TIM1_COMPB
TIM1_OVF
TIM0_COMPA
TIM0_COMPB
TIM0_OVF
ANA_COMP
ADC
EE_RDY
USI_STR
USI_OVF
r16, high(RAMEND); Main program start
SPH,r16
r16, low(RAMEND)
SPL,r16
25.
Comments
; Reset Handler
; IRQ0 Handler
; PCINT0 Handler
; PCINT1 Handler
; Watchdog Interrupt Handler
; Timer1 Capture Handler
; Timer1 Compare A Handler
; Timer1 Compare B Handler
; Timer1 Overflow Handler
; Timer0 Compare A Handler
; Timer0 Compare B Handler
; Timer0 Overflow Handler
; Analog Comparator Handler
; ADC Conversion Handler
; EEPROM Ready Handler
; USI STart Handler
; USI Overflow Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
50. When the INT0 interrupt is enabled
8183D–AVR–04/11