ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 10

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.4.1
6.5
6.6
6.7
8330B–AVR–10/11
Program Flow
Status Register
Stack and Stack Pointer
Hardware Multiplier
The multiplier is capable of multiplying two 8-bit numbers into a 16-bit result. The hardware mul-
tiplier supports different variations of signed and unsigned integer and fractional numbers:
A multiplication takes two CPU clock cycles.
After reset, the CPU starts to execute instructions from the lowest address in the flash program-
memory ‘0.’ The program counter (PC) addresses the next instruction to be fetched.
Program flow is provided by conditional and unconditional jump and call instructions capable of
addressing the whole address space directly. Most AVR instructions use a 16-bit word format,
while a limited number use a 32-bit format.
During interrupts and subroutine calls, the return address PC is stored on the stack. The stack is
allocated in the general data SRAM, and consequently the stack size is only limited by the total
SRAM size and the usage of the SRAM. After reset, the stack pointer (SP) points to the highest
address in the internal SRAM. The SP is read/write accessible in the I/O memory space,
enabling easy implementation of multiple stacks or stack areas. The data SRAM can easily be
accessed through the five different addressing modes supported in the AVR CPU.
The status register (SREG) contains information about the result of the most recently executed
arithmetic or logic instruction. This information can be used for altering program flow in order to
perform conditional operations. Note that the status register is updated after all ALU operations,
as specified in the instruction set reference. This will in many cases remove the need for using
the dedicated compare instructions, resulting in faster and more compact code.
The status register is not automatically stored when entering an interrupt routine nor restored
when returning from an interrupt. This must be handled by software.
The status register is accessible in the I/O memory space.
The stack is used for storing return addresses after interrupts and subroutine calls. It can also be
used for storing temporary data. The stack pointer (SP) register always points to the top of the
stack. It is implemented as two 8-bit registers that are accessible in the I/O memory space. Data
are pushed and popped from the stack using the PUSH and POP instructions. The stack grows
from a higher memory location to a lower memory location. This implies that pushing data onto
the stack decreases the SP, and popping data off the stack increases the SP. The SP is auto-
matically loaded after reset, and the initial value is the highest address of the internal SRAM. If
the SP is changed, it must be set to point above address 0x2000, and it must be defined before
any subroutine calls are executed or before interrupts are enabled.
•Multiplication of unsigned integers
•Multiplication of signed integers
•Multiplication of a signed integer with an unsigned integer
•Multiplication of unsigned fractional numbers
•Multiplication of signed fractional numbers
•Multiplication of a signed fractional number with an unsigned one
XMEGA B1
10