SAM9263 Atmel Corporation, SAM9263 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM9263
Manufacturer Part Number
SAM9263
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.M40800.pdf
(153 pages)
3.SAM9260.pdf
(290 pages)
4.SAM9261.pdf
(248 pages)
5.SAM9263.pdf
(1109 pages)
6.SAM9263.pdf
(51 pages)
Specifications of SAM9263
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
240 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
4
Can
1
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
Yes
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
96
Self Program Memory
NO
External Bus Interface
2
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Fpu
No
Mpu / Mmu
No / Yes
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
EBI: External Bus
Interface
External Memory
Mapping
18
AT91X40 Series
The EBI generates the signals that control the access to the external memory or periph-
eral devices. The EBI is fully-programmable and can address up to 64M bytes. It has
eight chip selects and a 24-bit address bus, the upper four bits of which are multiplexed
with a chip select.
The 16-bit data bus can be configured to interface with 8- or 16-bit external devices.
Separate read and write control signals allow for direct memory and peripheral
interfacing.
The EBI supports different access protocols allowing single-clock cycle memory
accesses.
The main features are:
•
•
•
•
•
•
•
•
•
The “EBI User Interface” is described on page 45.
The memory map associates the internal 32-bit address space with the external 24-bit
address bus.
The memory map is defined by programming the base address and page size of the
external memories (see “EBI User Interface” registers EBI_CSR0 to EBI_CSR7). Note
that A0 - A23 is only significant for 8-bit memory; A1 - A23 is used for 16-bit memory.
If the physical memory device is smaller than the programmed page size, it wraps
around and appears to be repeated within the page. The EBI correctly handles any valid
access to the memory device within the page (see Figure 6).
In the event of an access request to an address outside any programmed page, an
Abort signal is generated. Two types of Abort are possible: instruction prefetch abort
and data abort. The corresponding exception vector addresses are respectively
0x0000000C and 0x00000010. It is up to the system programmer to program the error
handling routine to use in case of an Abort (see the ARM7TDMI datasheet for further
information).
If two chip selects are defined as having the same base address, an access to the over-
lapping address space asserts both NCS lines. The Chip Select Register with the
smaller number defines the characteristics of the external access and the behavior of
the control signals.
External memory mapping
Up to 8 chip select lines
8- or 16-bit data bus
Byte write or byte select lines
Remap of boot memory
Two different read protocols
Programmable wait state generation
External wait request
Programmable data float time
1354D–ATARM–08/02