ATmega48PA Automotive Atmel Corporation, ATmega48PA Automotive Datasheet - Page 143
ATmega48PA Automotive
Manufacturer Part Number
ATmega48PA Automotive
Description
Manufacturer
Atmel Corporation
- Current page: 143 of 225
- Download datasheet (4Mb)
18.6
18.6.1
18.6.2
7701E–AVR–02/11
Changing Channel or Reference Selection
ADC Input Channels
ADC Voltage Reference
The MUX5:0 and REFS1:0 bits in the ADMUX register are single-buffered through a tempo-
rary register to which the CPU has random access. This ensures that the channel and
reference selection only takes place at a safe point during the conversion. The channel and
reference selection is continuously updated until a conversion is started. Once the conversion
starts, the channel and reference selection is locked to ensure a sufficient sampling time for
the ADC. Continuous updating resumes in the last ADC clock cycle before the conversion
completes (ADIF in ADCSRA is set). Note that the conversion starts on the following rising
ADC clock edge after ADSC is written. The user is thus advised not to write new channel or
reference selection values to ADMUX until one ADC clock cycle after ADSC is written.
If auto triggering is used, the exact time of the triggering event can be indeterministic. Special
care must be taken when updating the ADMUX register in order to control which conversion
will be affected by the new setting.
If both ADATE and ADEN are written to logical one, an interrupt event can occur at any time. If
the ADMUX register is changed in this period, the user cannot tell if the next conversion is
based on the old or the new setting. The ADMUX register can be safely updated in the follow-
ing ways:
When updating the ADMUX register in one of these conditions, the new setting will affect the
next ADC conversion.
When changing channel selections, the user should observe the following guidelines to ensure
that the correct channel is selected:
In single-conversion mode, always select the channel before starting the conversion. The
channel selection may be changed one ADC clock cycle after writing logical one to ADSC.
However, the simplest method is to wait for the conversion to complete before changing the
channel selection.
In free running mode, always select the channel before starting the first conversion. The chan-
nel selection may be changed one ADC clock cycle after writing logical one to ADSC.
However, the simplest method is to wait for the first conversion to complete, and then change
the channel selection. Because the next conversion has already started automatically, the
next result will reflect the previous channel selection. Subsequent conversions will reflect the
new channel selection.
The reference voltage for the ADC (V
gle-ended channels that exceed V
as either V
after switching the reference voltage source may be inaccurate, and the user is advised to dis-
card this result.
a. When ADATE or ADEN is cleared.
b. During conversion, minimum one ADC clock cycle after the trigger event.
c. After a conversion, before the Interrupt Flag used as the trigger source is cleared.
CC
, internal 1.1V reference, or external AREF pin. The first ADC conversion result
Atmel ATtiny24/44/84 [Preliminary]
REF
will result in codes close to 0x3FF. V
REF
) indicates the conversion range for the ADC. Sin-
REF
can be selected
143
Related parts for ATmega48PA Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MCU AVR 4K ISP FLASH 20MHZ 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
MCU AVR 4K ISP FLSH 20MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4K ISP FLASH 20MHZ 28DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 32TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 28-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4K FLASH 20MHZ 28QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet: