LT1715CMS#PBF Linear Technology, LT1715CMS#PBF Datasheet - Page 14
![IC COMPARATOR 150MHZ DUAL 10MSOP](/photos/1/36/13608/10-msop_05-08-1661_sml.jpg)
LT1715CMS#PBF
Manufacturer Part Number
LT1715CMS#PBF
Description
IC COMPARATOR 150MHZ DUAL 10MSOP
Manufacturer
Linear Technology
Series
UltraFast™r
Type
General Purposer
Specifications of LT1715CMS#PBF
Number Of Elements
2
Output Type
CMOS, Rail-to-Rail, TTL
Voltage - Supply
2.7 V ~ 12 V
Mounting Type
Surface Mount
Package / Case
10-TFSOP, 10-MSOP (0.118", 3.00mm Width)
Comparator Type
High Speed
No. Of Comparators
2
Response Time
4ns
Ic Output Type
CMOS, TTL
Supply Current
1mA
Supply Voltage Range
2.7V To 12V
Amplifier Case Style
MSOP
No. Of Pins
10
Rohs Compliant
Yes
Output Compatibility
CMOS, TTL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LT1715
APPLICATIO S I FOR ATIO
the frequency-dependent increase in power consumption.
The frequency dependence of the supply current is shown
in the Typical Performance Characteristics.
Speed Limits
The LT1715 comparator is intended for high speed appli-
cations, where it is important to understand a few limita-
tions. These limitations can roughly be divided into three
categories: input speed limits, output speed limits, and
internal speed limits.
There are no significant input speed limits except the
shunt capacitance of the input nodes. If the 2pF typical
input nodes are driven, the LT1715 will respond.
The output speed is constrained by three mechanisms, the
first of which is the slew currents available from the output
transistors. To maintain low power quiescent operation,
the LT1715 output transistors are sized to deliver 35mA to
60mA typical slew currents. This is sufficient to drive small
capacitive loads and logic gate inputs at extremely high
speeds. But the slew rate will slow dramatically with heavy
capacitive loads. Because the propagation delay (t
definition ends at the time the output voltage is halfway
between the supplies, the fixed slew current makes the
LT1715 faster at 3V than 5V with large capacitive loads and
sufficient input overdrive.
Another manifestation of this output speed limit is skew,
the difference between t
the LT1715 vary with the process variations of the PNP
and NPN transistors, for rising edges and falling edges
respectively. The typical 0.5ns skew can have either polar-
ity, rising edge or falling edge faster. Again, the skew will
increase dramatically with heavy capacitive loads.
A final limit to output speed is the turn-on and turn-off time
of the output devices. Each device has substantial base
charge that requires one nanosecond or more of active
charging or discharging by the bias current of the Darlington
driver stage. When toggle rates are high enough that insuf-
ficient time is allowed for this turn-on or turn-off, glitches
may occur leading to dropout or runt pulses. Furthermore,
power consumption may increase nonlinearly if devices
are not turned off before the opposing cycle. However,
once the toggle frequency increases or decreases, the part
14
U
PD
U
+
and t
PD
–
W
. The slew currents of
U
PD
)
will easily leave this undesired operating mode no worse
for the wear provided there is adequate heat sinking to
prevent thermal overload. At frequencies well beyond the
maximum toggle rate, the part will toggle with limited output
swing and well controlled power consumption.
The internal speed limits manifest themselves as disper-
sion. All comparators have some degree of dispersion,
defined as a change in propagation delay versus input
overdrive. The propagation delay of the LT1715 will vary
with overdrive, from a typical of 4ns at 20mV overdrive to
6ns at 5mV overdrive (typical). The LT1715’s primary
source of dispersion is the hysteresis stage. As a change
of polarity arrives at the gain stage, the positive feedback
of the hysteresis stage subtracts from the overdrive avail-
able. Only when enough time has elapsed for a signal to
propagate forward through the gain stage, backwards
through the hysteresis path and forward through the gain
stage again, will the output stage receive the same level of
overdrive that it would have received in the absence of
hysteresis.
The LT1715 is several hundred picoseconds faster when
V
to the internal speed limit; the gain stage operates between
V
bias due to reduced silicon junction capacitances.
In many applications, as shown in the following examples,
there is plenty of input overdrive. Even in applications
providing low levels of overdrive, the LT1715 is fast
enough that the absolute dispersion of 2ns (= 6 – 4) is
often small enough to ignore.
The gain and hysteresis stage of the LT1715 is simple,
short and high speed to help prevent parasitic oscilla-
tions while adding minimum dispersion. This internal
“self-latch” can be usefully exploited in many applica-
tions because it occurs early in the signal chain, in a low
power, fully differential stage. It is therefore highly im-
mune to disturbances from other parts of the circuit,
such as the output, or on the supply lines. Once a high
speed signal trips the hysteresis, the output will respond,
after some propagation delay, without regard to these
external influences that can cause trouble in nonhysteretic
comparators.
EE
EE
= – 5V, relative to single supply operation. This is due
and + V
S
, and it is faster with higher reverse voltage