DS2433 Maxim, DS2433 Datasheet - Page 11

no-image

DS2433

Manufacturer Part Number
DS2433
Description
The DS2433 4Kb 1-Wire® EEPROM identifies and stores relevant information about the product to which it is associated
Manufacturer
Maxim
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS2433+
Manufacturer:
Maxim Integrated
Quantity:
271
Part Number:
DS2433-Z01
Manufacturer:
Maxim Integrated
Quantity:
497
Part Number:
DS2433AX-S#T
Manufacturer:
Maxim Integrated
Quantity:
282
Part Number:
DS2433AX-S+TW
Manufacturer:
Maxim Integrated
Quantity:
459
Part Number:
DS2433D+&TR
Manufacturer:
XILINX
Quantity:
200
Part Number:
DS2433D/T&R
Manufacturer:
Maxim Integrated
Quantity:
326
Company:
Part Number:
DS2433S
Manufacturer:
MAXIM
Quantity:
429
Part Number:
DS2433S
Manufacturer:
DALLAS
Quantity:
225
Part Number:
DS2433S+
Manufacturer:
Maxim
Quantity:
14 356
Company:
Part Number:
DS2433S+
Manufacturer:
MAXIM
Quantity:
402
Part Number:
DS2433S+T&R
Manufacturer:
MAXIM
Quantity:
1 248
Part Number:
DS2433S+T&R
Manufacturer:
MAXIM
Quantity:
285
Part Number:
DS2433S+TR
Manufacturer:
MAXIM
Quantity:
8 000
Part Number:
DS2433S+TR
Manufacturer:
MAXIM
Quantity:
251
Part Number:
DS2433S-500-00+T&R
Manufacturer:
MAXIM
Quantity:
700
Figure 8. HARDWARE CONFIGURATION
1-Wire BUS SYSTEM
The 1-Wire bus is a system which has a single bus master and one or more slaves. In all instances the
DS2433 is a slave device. The bus master is typically a microcontroller. The discussion of this bus system
is broken down into three topics: hardware configuration, transaction sequence, and 1-Wire signaling
(signal types and timing). A 1-Wire protocol defines bus transactions in terms of the bus state during
specific time slots that are initiated on the falling edge of sync pulses from the bus master.
HARDWARE CONFIGURATION
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open
drain or 3-state outputs. The 1-Wire port of the DS2433 is open drain with an internal circuit equivalent
to that shown in Figure 8. A multidrop bus consists of a 1-Wire bus with multiple slaves attached. At
regular speed the 1-Wire bus has a maximum data rate of 16.3kbps. The speed can be boosted to 142kbps
by activating the Overdrive Mode. The 1-Wire bus requires a pullup resistor of approximately 5k.
The idle state for the 1-Wire bus is high. If for any reason a transaction needs to be suspended, the bus
MUST be left in the idle state if the transaction is to resume. If this does not occur and the bus is left low
for more than 16s (Overdrive Speed) or more than 120s (regular speed), one or more devices on the
bus may be reset.
TRANSACTION SEQUENCE
The protocol for accessing the DS2433 via the 1-Wire port is as follows:
 Initialization
 ROM Function Command
 Memory Function Command
 Transaction/Data
*5k IS ADEQUATE FOR READING THE DS2433. TO WRITE TO A SINGLE DEVICE, A 2.2k RESISTOR AND V
SUFFICIENT. FOR WRITING MULTIPLE DS2433s SIMULTANEOUSLY OR OPERATION AT LOW V
BY A LOW-IMPEDANCE PULLUP TO V
COMMUNICATION SPEED AND THE BUS LOAD CHARACTERISTICS, THE OPTIMAL PULLUP RESISTOR (R
1.5k TO 5k RANGE.
PUP
WHILE THE DEVICE COPIES THE SCRATCHPAD TO EEPROM. DEPENDING ON THE 1-Wire
R
PU
*
11 of 23
PUP
, THE R
PU
PU
) VALUE WILL BE IN THE
PUP
SHOULD BE BYPASSED
OF AT LEAST 4.0V IS
DS2433

Related parts for DS2433