STVM100DS6F STMicroelectronics, STVM100DS6F Datasheet
STVM100DS6F
Specifications of STVM100DS6F
STVM100DS6F
Available stocks
Related parts for STVM100DS6F
STVM100DS6F Summary of contents
Page 1
... TSSOP8 package Applications ■ TFT-LCD panels Table 1. Device summary Order code Optimum temperature range STVM100DC6E STVM100DS6F November 2009 DD setting COM Description The STVM100 is a programmable VCOM adjust- ment solution for thin-film transistor (TFT) liquid- crystal displays (LCDs) to remove “flickers”. It can ...
Page 2
Contents Contents 1 Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
STVM100 List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of figures List of figures Figure 1. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
STVM100 1 Device overview Figure 1. Logic diagram Table 2. Pin names and functions Name Type OUT Analog AV Supply DD WP Input GND V Supply DD SDA Input/Output I SCL Input SET Analog 1. See SET pin function in ...
Page 6
Device overview Figure 2. Connections diagram Figure 3. Block diagram SDA SCL WP Figure 4. Hardware hookup MCU 6/27 SET OUT SCL 2 7 SDA GND ...
Page 7
STVM100 2 Device operation The STVM100 operates as a slave device on the serial bus. Access is obtained by implementing a start condition, followed by the 7-bit slave address (1001111), and the eighth bit for READ/WRITE identification. The volatile DAC ...
Page 8
Device operation 2.1.4 Data valid The data on the SDA line must be stable during the high period of the clock. The high or low state of the data line can only change when the clock signal on the SCL ...
Page 9
STVM100 2.1.5 Acknowledge Each byte of eight bits is followed by one acknowledge bit. This acknowledge bit is a low level signal put on the bus by the receiver, whereas the master generates an extra acknowledge-related clock pulse (see obliged ...
Page 10
Device operation 2.2 Read mode In READ mode, after the start condition, the master sets the slave address (see Followed by the READ/WRITE mode control bit (R/W=1) and the acknowledge bit, the value in DAC register will be transmitted and ...
Page 11
STVM100 3 Application information The STVM100 is a programmable V provides a digital I external resistive voltage divider, which can then be applied to an external V The highest and lowest V connection is shown in The sink current from ...
Page 12
Application information If the user-selected value is 0 (zero scale), the minimum current is sunk. The maximum V value is obtained in COM Equation 3 If the user-selected value is 127 (full scale), the maximum current is sunk and the ...
Page 13
... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 4. ...
Page 14
DC and AC parameters 5 DC and AC parameters This section summarizes the operating measurement conditions, and the dc and ac characteristics of the device. The parameters in the DC and AC characteristics tables that follow, are derived from tests ...
Page 15
STVM100 Table 7. DC and AC characteristics Sym Description Supply voltage EEPROM V DD programming supply voltage ( supply current Analog supply voltage DD ( supply current AVDD DD SET SET voltage resolution ...
Page 16
DC and AC parameters Figure 9. Bus timing requirements sequence SDA tBUF SCL P Table 8. AC characteristics Sym Description f SCL clock frequency SCL t Clock low period LOW t Clock high period HIGH t Data setup time SU:DAT ...
Page 17
STVM100 6 Typical operating characteristics Typical operating characteristics for the STVM100 are T OUT = 1/2AV , and R DD Figure 10 Figure 11 ...
Page 18
Typical operating characteristics Figure 12 Figure 13 18/27 supply current vs. temperature -40 -30 -20 - Temperature°C supply current vs. temperature ...
Page 19
STVM100 Figure 14. I OUT Figure 15. Total unadjusted error vs. DAC setting error vs. temperature (STVM100 at middle scale) 0.06 0.05 0.04 0.03 0.02 0.01 0 -40 - Temperature°C 0.022474 0.020395 0.018316 0.016237 0.014158 0.012079 0.01 1 ...
Page 20
Typical operating characteristics Figure 16. Differential non-linearity vs. DAC setting Figure 17. Integral non-linearity vs. DAC setting 20/27 0.2 0.15 0.1 0.05 0 -0.05 -0.1 -0.15 -0 DAC setting (decimal) 0.3 0.2 0.1 0 ...
Page 21
STVM100 Figure 18 Figure 19. Full scale-up response power-up response 5ms/DIV AV : 5V/DIV 5V/DIV 20µs/DIV SCL: 5V/DIV, SDA: 5V/DIV, V Doc ID 13236 Rev 7 Typical operating characteristics : 1V/DIV ...
Page 22
Typical operating characteristics Figure 20. Full scale-down response 22/27 20µs/DIV SCL: 5V/DIV, SDA: 5V/DIV, V OUT Doc ID 13236 Rev 7 STVM100 : 1V/DIV 1V/DIV SET ...
Page 23
STVM100 7 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ...
Page 24
Package mechanical data Figure 22. TSSOP8 – 8-lead, thin shrink small outline mm, mech. data A CP Note: Drawing is not to scale. Table 10. TSSOP8 – 8-lead, thin shrink small outline, 3mm x 3mm, mech. ...
Page 25
STVM100 8 Part numbering Table 11. Ordering information scheme Example: Device type STVM100, V calibrator with 7-bit DAC and I COM Package DC = TDFN8 DS = TSSOP8 Temperature range 6 = –40 to 85°C Shipping method ® ...
Page 26
Revision history 9 Revision history Table 12. Document revision history Date 09-May-2006 14-Jul-2006 08-Nov-2006 12-Feb-2007 20-Apr-2007 24-Jul-2007 04-Nov-2009 26/27 Revision 1 Initial release. 2 Graphical and textual updates Document status upgraded to Preliminary Data; changed the wording of Input function ...
Page 27
... STVM100 Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...