M25P32 Numonyx, B.V., M25P32 Datasheet - Page 13
![no-image](/images/no-image-200.jpg)
M25P32
Manufacturer Part Number
M25P32
Description
32-Mbit, low voltage, serial Flash memory with 75 MHz SPI bus interface
Manufacturer
Numonyx, B.V.
Datasheet
1.M25P32.pdf
(53 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
M25P32
Manufacturer:
ST
Quantity:
20 000
Part Number:
M25P32-VME6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
M25P32-VME6G
Manufacturer:
Numonyx/ST Micro
Quantity:
34 441
Company:
Part Number:
M25P32-VME6G
Manufacturer:
MICRON
Quantity:
2 180
Part Number:
M25P32-VME6G
Manufacturer:
MICRON/镁光
Quantity:
20 000
Company:
Part Number:
M25P32-VME6TG
Manufacturer:
MICRON
Quantity:
1 000
Company:
Part Number:
M25P32-VME6TG
Manufacturer:
NUMONYX
Quantity:
12 550
Part Number:
M25P32-VME6TG
Manufacturer:
MICRON
Quantity:
20 000
M25P32
4
4.1
4.2
4.3
4.4
4.5
Operating features
Page Programming
To program one data byte, two instructions are required: Write Enable (WREN), which is one
byte, and a Page Program (PP) sequence, which consists of four bytes plus data. This is
followed by the internal Program cycle (of duration t
To spread this overhead, the Page Program (PP) instruction allows up to 256 bytes to be
programmed at a time (changing bits from 1 to 0), provided that they lie in consecutive
addresses on the same page of memory.
For optimized timings, it is recommended to use the Page Program (PP) instruction to
program all consecutive targeted bytes in a single sequence versus using several Page
Program (PP) sequences with each containing only a few bytes (see
Sector Erase and Bulk Erase
The Page Program (PP) instruction allows bits to be reset from 1 to 0. Before this can be
applied, the bytes of memory need to have been erased to all 1s (FFh). This can be
achieved either a sector at a time, using the Sector Erase (SE) instruction, or throughout the
entire memory, using the Bulk Erase (BE) instruction. This starts an internal Erase cycle (of
duration t
The Erase instruction must be preceded by a Write Enable (WREN) instruction.
Polling during a Write, Program or Erase cycle
A further improvement in the time to Write Status Register (WRSR), Program (PP) or Erase
(SE or BE) can be achieved by not waiting for the worst case delay (t
Write In Progress (WIP) bit is provided in the Status Register so that the application program
can monitor its value, polling it to establish when the previous Write cycle, Program cycle or
Erase cycle is complete.
Fast Program/Erase mode
The Fast Program/Erase mode is used to speed up programming/erasing. The device
enters the Fast Program/Erase mode during the Page Program, Sector Erase or Bulk Erase
instruction whenever a voltage equal to V
The use of the Fast Program/Erase mode requires specific operating conditions in addition
to the normal ones (V
●
●
●
Active Power, Standby Power and Deep Power-down modes
When Chip Select (S) is Low, the device is selected, and in the Active Power mode.
the voltage applied to the W/V
ambient temperature, T
the cumulated time during which W/V
SE
or t
BE
).
CC
must be within the normal operating range):
A
must be 25 °C ±10 °C,
PP
pin must be equal to V
PPH
PP
is at V
is applied to the W/V
PP
PPH
).
should be less than 80 hours
PPH
(see
PP
W
Page Program
pin.
, t
Table
Operating features
PP
, t
SE
10)
, or t
BE
(PP)).
). The
13/53