S1D10605 Epson Electronics America, Inc., S1D10605 Datasheet - Page 234
S1D10605
Manufacturer Part Number
S1D10605
Description
S1d15000 Series Lcd Driver With Ram
Manufacturer
Epson Electronics America, Inc.
Datasheet
1.S1D10605.pdf
(612 pages)
- Current page: 234 of 612
- Download datasheet (5Mb)
Rev. 4.6
Reset
When power is turned ON, the S1D15600/601/602 series
is initialized on the rising edge of RES. Initial settings are
as follows.
RES should be connected to the microprocessor reset
terminal so that both devices are reset at the same time.
RES must be LOW for at least 1 s to correctly reset the
S1D15600/601/602 series. Normal operation starts 1 s
after the rising edge on RES.
10. Column address counter
11. Page address register
12. Output selection circuit
13. n-line inversion register
14. Set the electronic control register to zero (0).
1. Display
2. Display mode
3. n-line inversion
4. Duty cycle
5. ADC select
6. Read/write modify
7. Internal power supply
8. Serial interface register data : Cleared
9. Display initial line register : Line 1
: OFF
: Normal
: OFF
: 1/64 (S1D15600)
: Normal (D0 = L)
: OFF
: OFF
: 0
: Page 0
: Case 6
: 16
1/32 (S1D15601)
EPSON
If the built-in LCD power circuit of the S1D1560
is not used, the RES signal must be low when the external
LCD power supply is turned on. When the RES goes low,
each register is cleared to the above listed initial status.
However, the oscillation circuit and output pins (OSC2,
FR, SYNC, CLD, DYO, D0 to D7 pins) are not affected.
If the S1D15600 is not properly initialized when power
is turned ON, it can lock itself into a state that cannot be
cancelled.
Although S1D15600/601/602 Series devices maintain
the operation status under commands, when external
noise of excessive levels enters, their internal statys may
be changed. Consequently, it is necessary to provide
means to suppress noise occurring from package or the
system or orovide means to avoid influence of such
noise.
Also, to cope with sudden noise, we suggest you to set up
the software so the operation status can be periodically
refreshed.
When the Reset command is used, only initial settings 9
to 14 are active.
S1D15600/601/602 Series
*
D
**
7–39
B
*
Related parts for S1D10605
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Dc Solid State Relay
Manufacturer:
BRIGHT TOWARD INDUSTRIAL CO.,LTD.
Datasheet:
Part Number:
Description:
1.0A Surface Mount Glass Passivated Rectifier
Manufacturer:
Vishay Telefunken
Part Number:
Description:
1.0A SURFACE MOUNT GLASS PASSIVATED RECTIFIER
Manufacturer:
Won-Top Electronics
Part Number:
Description:
S1a - S1m General Purpose Rectifiers
Manufacturer:
Fairchild Semiconductor
Datasheet:
Part Number:
Description:
1 Amp Silicon Rectifier 50 to 1000 Volts
Manufacturer:
MCC [Micro Commercial Components]
Datasheet:
Part Number:
Description:
Optical Devicepbs-prism For Blue
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
Optical Device Ir-cut Filter
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
Optical Device
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
S1d12000 Series Lcd Driver Ic Technical Manual Technical Manual
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
S1d13521 Epd Controller
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
S1d13710 Mobile Graphics Engine
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
S1d13711 Mobile Graphics Engine
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
Liquid Crystal Display =lcd Driver
Manufacturer:
Epson Electronics America, Inc.
Datasheet:
Part Number:
Description:
Embedded Memory Graphics Lcd Controller
Manufacturer:
Epson Electronics America, Inc.
Datasheet: