FM24C16B Ramtron, FM24C16B Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/5/556/ramtron_sml.jpg)
FM24C16B
Manufacturer Part Number
FM24C16B
Description
16Kb Serial 5V F-RAM Memory
Manufacturer
Ramtron
Datasheet
1.FM24C16B.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FM24C16B-G
Manufacturer:
RAMTRON
Quantity:
125 000
Part Number:
FM24C16B-G
Manufacturer:
RAMTRON
Quantity:
20 000
Company:
Part Number:
FM24C16B-GTR
Manufacturer:
RAMTRON
Quantity:
5 000
Company:
Part Number:
FM24C16B-GTR
Manufacturer:
RAMTRON
Quantity:
5
Part Number:
FM24C16B-GTR
Manufacturer:
RAMTRON
Quantity:
20 000
www.DataSheet.co.kr
Read Operation
There are two types of read operations. They are
current address read and selective address read. In a
current address read, the FM24C16B uses the internal
address latch to supply the lower 8 address bits. In a
selective read, the user performs a procedure to set
these lower address bits to a specific value.
Current Address & Sequential Read
As mentioned above the FM24C16B uses an internal
latch to supply the lower 8 address bits for a read
operation. A current address read uses the existing
value in the address latch as a starting place for the
read operation. This is the address immediately
following that of the last operation.
To perform a current address read, the bus master
supplies a slave address with the LSB set to 1. This
indicates that a read operation is requested. The 3
page select bits in the slave ID specify the block of
memory that is used for the read operation. On the
next clock, the FM24C16B will begin shifting out
data from the current address. The current address is
the 3 bits from the slave ID combined with the 8 bits
that were in the internal address latch.
Beginning with the current address, the bus master
can read any number of bytes. Thus, a sequential read
is simply a current address read with multiple byte
transfers. After each byte, the internal address counter
will be incremented. Each time the bus master
acknowledges a byte this indicates that the
FM24C16B should read out the next sequential byte.
There are four ways to properly terminate a read
operation. Failing to properly terminate the read will
most likely create a bus contention as the FM24C16B
Rev. 1.3
July 2011
By FM24C16B
By Master
By FM24C16B
By Master
Start
S
Slave Address
Start
S
Slave Address
0
A
Figure 6. Multiple Byte Write
Figure 5. Single Byte Write
Address & Data
Word Address
0
A
Address & Data
Word Address
A
attempts to read out additional data onto the bus. The
four valid methods are as follows.
1.
2.
3.
4.
If the internal address reaches 7FFh it will wrap
around to 000h on the next read cycle. Figures 7 and
8 show the proper operation for current address reads.
Selective (Random) Read
A simple technique allows a user to select a random
address location as the starting point for a read
operation. It uses the first two bytes of a write
operation to set the internal address byte followed by
subsequent read operations.
To perform a selective read, the bus master sends out
the slave address with the LSB set to 0. This specifies
a write operation. According to the write protocol, the
bus master then sends the word address byte that is
loaded into the internal address latch. After the
FM24C16B acknowledges the word address, the bus
master issues a start condition. This simultaneously
aborts the write operation and allows the read
command to be issued with the slave address set to 1.
The operation is now a current address read. This
operation is illustrated in Figure 9.
The bus master issues a no-acknowledge in the
9
This is illustrated in the diagrams below. This is
the preferred method.
The bus master issues a no-acknowledge in the
9
The bus master issues a stop in the 9
cycle. Bus contention may result.
The bus master issues a start in the 9
cycle. Bus contention may result.
th
th
Acknowledge
Data Byte
clock cycle and a start in the 10
clock cycle and a stop in the 10
Acknowledge
A
FM24C16B - 16Kb 5V I2C F-RAM
Data Byte
A
Data Byte
A
Stop
P
th
th
.
clock cycle.
Page 6 of 12
A
Stop
th
th
P
clock
clock
Datasheet pdf - http://www.DataSheet4U.net/