PIC18F87J93 Microchip Technology, PIC18F87J93 Datasheet - Page 36
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC18F87J93
Manufacturer Part Number
PIC18F87J93
Description
LCD PIC18F Microcontroller
Manufacturer
Microchip Technology
Datasheet
1.PIC18F87J93.pdf
(54 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F87J93-I/PT
Manufacturer:
Microchip
Quantity:
472
Company:
Part Number:
PIC18F87J93-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC18F87J93T-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
www.DataSheet4U.com
conversion sample. This means the ADRESH:ADRESL
PIC18F87J93 FAMILY
2.5
Figure 2-3 shows the operation of the A/D converter
after the GO/DONE bit has been set and the
ACQT<2:0> bits are cleared. A conversion is started
after the following instruction to allow entry into Sleep
mode before the conversion begins.
Figure 2-4 shows the operation of the A/D converter
after the GO/DONE bit has been set; the ACQT<2:0>
bits are set to ‘010’ and a 4 T
selected before the conversion starts.
Clearing the GO/DONE bit during a conversion will abort
the current conversion. The A/D Result register pair will
NOT be updated with the partially completed A/D
registers will continue to contain the value of the last
completed conversion (or the last value written to the
ADRESH:ADRESL registers).
After the A/D conversion is completed or aborted, a
2 T
started. After this wait, acquisition on the selected
channel is automatically started.
FIGURE 2-3:
FIGURE 2-4:
DS39948A-page 34
Note:
(Holding capacitor continues
acquiring input)
AD
Set GO/DONE bit
wait is required before the next acquisition can be
1
T
CY
Set GO/DONE bit
Holding capacitor is disconnected from analog input (typically 100 ns)
A/D Conversions
T
- T
Automatic
Acquisition
Time
ACQT
The GO/DONE bit should NOT be set in
the same instruction that turns on the A/D.
2
AD
Conversion starts
T
Cycles
AD
3
1 T
A/D CONVERSION T
A/D CONVERSION T
AD
b9
4
2 T
Conversion starts
(Holding capacitor is disconnected)
AD
b8
AD
1
3 T
acquisition time is
AD
b7
b9
Next Q4: ADRESH:ADRESL is loaded, GO/DONE bit is cleared,
2
4 T
Next Q4: ADRESH:ADRESL is loaded, GO/DONE bit is cleared,
AD
b6
b8
3
AD
5 T
AD
ADIF bit is set, holding capacitor is connected to analog input.
CYCLES (ACQT<2:0> = 000, T
CYCLES (ACQT<2:0> = 010, T
Preliminary
AD
ADIF bit is set, holding capacitor is reconnected to analog input.
b5
b7
4
6 T
AD
b4
T
5
b6
7 T
AD
Cycles
2.6
An A/D conversion can be started by the “Special Event
Trigger” of the CCP2 module. This requires that the
CCP2M<3:0> bits (CCP2CON<3:0>) be programmed
as ‘1011’ and that the A/D module is enabled (ADON
bit is set). When the trigger occurs, the GO/DONE bit
will be set, starting the A/D acquisition and conversion,
and the Timer1 (or Timer3) counter will be reset to zero.
Timer1 (or Timer3) is reset to automatically repeat the
A/D acquisition period with minimal software overhead
(moving ADRESH:ADRESL to the desired location).
The appropriate analog input channel must be selected
and the minimum acquisition period is either timed by
the user, or an appropriate T
the Special Event Trigger sets the GO/DONE bit (starts
a conversion).
If the A/D module is not enabled (ADON is cleared), the
Special Event Trigger will be ignored by the A/D module
but will still reset the Timer1 (or Timer3) counter.
AD
b3
b5
6
8
T
AD
b2
Use of the CCP2 Trigger
b4
7
9 T
AD
b1
b3
10
8
T
AD
b0
ACQ
ACQ
b2
11
9
© 2009 Microchip Technology Inc.
= 0)
= 4 T
ACQ
10
b1
time is selected before
AD
b0
)
11