ISL95311 Intersil Corporation, ISL95311 Datasheet - Page 6

• Manufacturer Part Number: ISL95311
• Description: 128 Taps I2C Interface
• Manufacturer: Intersil Corporation

NOTES:
Pin Descriptions
Potentiometer Pins
R
R
wiper and not the voltage potential on the terminals. With
WR set to 127, the wiper will be closest to R
WR set to 00, the wiper is closest to R
R
R
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WR.
Bus Interface Pins
SERIAL DATA INPUT/OUTPUT (SDA)
The SDA is a bidirectional serial data input/output pin for the
I
wiper register address and data from a I
device at the rising edge of the serial clock SCL, and it shifts
out data after each falling edge of the serial clock SCL.
SDA requires an external pull-up resistor, since it’s an open
drain input/output.
SERIAL CLOCK (SCL)
This input is the serial clock of the I
SCL requires an external pull-up resistor, since it’s an open
drain input.
10. RDNL = (R
12.
13. This parameter is not 100% tested.
14. t
11. RINL = [R
2
1. Typical values are for T
2. LSB: [V(R
3. ZS error = V(R
4. FS error = [V(R
5. DNL = [V(R
6. INL = V(R
7.
8. MI =
9. Roffset = R
L
W
W
C interface. It receives device address, operation code,
H
and R
incremental voltage when changing from one tap to an adjacent tap.
for i = 16 to 120 decimal, T = -40°C to 85°C. Max( ) is the maximum value of the wiper voltage and Min ( ) is the minimum value of the wiper
voltage over the temperature range.
Roffset = R
for i = 16 to 127, T = -40°C to 85°C. Max( ) is the maximum value of the resistance and Min ( ) is the minimum value of the resistance over the
temperature range.
valid STOP condition at the end of a Write sequence of a I
write cycle.
TC
TC
and R
is the wiper terminal and is equivalent to the movable
WP
R
V
is the minimum cycle time to be allowed for any non-volatile Write by the user, unless Acknowledge Polling is used. It is the time from a
|
R
=
=
H
127
L
--------------------------------------------------------------------------------------------- -
[
--------------------------------------------------------------- -
[
are referenced to the relative position of the
Max V RW
Max Ri
W
W
i
[
Max V RW
Max Ri
– (MI • i) – R
i
0
127
W
– R
)
)
– R
127
i
/ MI, when measuring between R
)
– (i • LSB – V(R
i
(
(
W
0
/ MI, when measuring between R
W
– V(R
(
i-1
(
|
– V(R
)
(
)
0
/ 127. R
)
) / MI, for i = 16 to 127.
127
(
/ LSB.
+
) Min Ri
–
Min Ri
W
)
– V+] / LSB.
W
i
)
A
)
)
0
i-1
i
)
+
) Min V RW
] / MI, for i = 16 to 127.
(
0
127
= 25°C and 3.3V supply voltage.
] / LSB-1, for i = 1 to 127. i is the DCP register setting.
–
] / 127. V(R
(
Min V RW
)
and R
] 2 ⁄
6
W
)
(
]
)
(
0
(
) for i = 1 to 127.
×
(
0
---------------- -
125°C
2
C serial interface.
10
are the measured resistances for the DCP register set to 7F hex and 00 hex respectively.
W
)
L
i
)
6
)
)
127
.
i
] 2 ⁄
2
)
C external master
and V(R
×
H
W
---------------- -
125°C
, and with the
10
W
and R
6
and R
W
)
L
0
.
are V(R
H
.
2
C serial interface Write operation, to the end of the self-timed internal non-volatile
ISL95311
W
) for the DCP register set to 7F hex and 00 hex respectively. LSB is the
DEVICE ADDRESS (A1–A0)
The Address inputs are used to set the least significant 2 bits
of the 8-bit I
address serial data stream must be made with the Address
input pins in order to initiate communication with the
ISL95311. A maximum of 4 ISL95311 devices may occupy
the I
Principles of Operation
The ISL95311 is an integrated circuit incorporating one DCP
with their associated register, non-volatile memory, and a
I
a host and the potentiometers and memory. The resistor
array is comprised of 127 individual resistors connected in
series. At either end of the array and between each resistor
is an electronic switch between that point and the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions.
When the device is powered-down, the last wiper position
stored will be maintained in the nonvolatile memory. When
power is restored, the contents of the memory are recalled
and the wiper is set to the value last stored.
2
C serial interface providing direct communication between
2
C serial bus.
2
C interface slave address. A match in the slave
May 6, 2005
FN8084.0