MACH211SP-10 Advanced Micro Devices, MACH211SP-10 Datasheet - Page 19

• Manufacturer Part Number: MACH211SP-10
• Description: High-Density EE CMOS Programmable Logic
• Manufacturer: Advanced Micro Devices

ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . –65 C to +150 C
Ambient Temperature
with Power Applied. . . . . . . . . . . . . . –55 C to +125 C
Supply Voltage with
Respect to Ground . . . . . . . . . . . . . . . –0.5 V to +7.0 V
DC Input Voltage . . . . . . . . . . . .–0.5 V to V
DC Output or
I/O Pin Voltage . . . . . . . . . . . . . .–0.5 V to V
Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V
Latchup Current (T
Stresses above those listed under Absolute Maximum
Ratings may cause permanent device failure. Functionality at
or above these limits is not implied. Exposure to Absolute
Maximum Ratings for extended periods may affect device
reliability. Programming conditions may differ.
DC CHARACTERISTICS over INDUSTRIAL operating ranges unless otherwise specified
Notes:
1. These are absolute values with respect to device ground and all overshoots due to system and/or tester noise are included.
2. I/O pin leakage is the worst case of I
3. Not more than one output should be shorted at a time. Duration of the short-circuit should not exceed one second.
4. This parameter is measured in low-power mode with a 16-bit up/down counter pattern. This pattern is programmed in each
5. This parameter is not 100% tested, but is evaluated at initial characterization and at any time the design is modified where
Parameter
Symbol
V
PAL block and is capable of being loaded, enabled and reset.
capacitance may be affected.
I
V
I
V
OUT
V
OZH
I
V
OZL
I
I
I
CC
SC
OH
IH
OL
IL
IH
IL
= 0.5 V has been chosen to avoid test problems caused by tester ground degradation.
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input HIGH Leakage Current
Input LOW Leakage Current
Off-State Output Leakage
Current HIGH
Off-State Output Leakage
Current LOW
Output Short-Circuit Current
Supply Current (Static)
Supply Current (Active)
Parameter Description
A
= –40 C to 85 C) . . . . . . 200 mA
IL
and I
OZL
MACH211SP-14/18/24 (Ind)
CC
I
I
Guaranteed Input Logical HIGH
Voltage for all Inputs (Note 1)
Guaranteed Input Logical LOW
Voltage for all Inputs (Note 1)
V
V
V
V
V
V
CC
V
V
V
OH
OL
OUT
OUT
OUT
IN
IN
IN
IN
CC
CC
(or I
+ 0.5 V
+ 0.5 V
= 16 mA, V
= –3.2 mA, V
= 5.25 V, V
= 0 V, V
= V
= V
= 5 V, T
= 5 V, T
= 5.25 V, V
= 0 V, V
= 0.5 V, V
IH
IH
IH
and I
or V
or V
CC
A
A
Test Conditions
CC
IL
IL
= 25 C, f = 0 MHz (Note 4)
= 25 C, f = 1 MHz (Note 4)
OZH
CC
= Max (Note 2)
CC
CC
(Note 2)
(Note 2)
CC
= Max
CC
= Max (Note 2)
= Min, V
OPERATING RANGES
Industrial (I) Devices
Ambient Temperature (T
Operating in Free Air. . . . . . . . . . . . . .–40 C to +85 C
Supply Voltage (V
with Respect to Ground . . . . . . . . . . +4.5 V to +5.5 V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
).
= Max (Notes 3, 5)
= Max
= Min, V
IN
IN
= V
= V
IH
IH
or V
or V
CC
IL
IL
)
A
Min
–30
2.4
2.0
)
Typ
40
45
–160
Max
–10
–10
0.5
0.8
10
10
Unit
mA
mA
mA
V
V
V
V
A
A
A
A
19