ADP3208C ON Semiconductor, ADP3208C Datasheet - Page 40
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ADP3208C
Manufacturer Part Number
ADP3208C
Description
7-bit,programmable,dual- Phase,mobile,cpu,synchronous Buck Controller
Manufacturer
ON Semiconductor
Datasheet
1.ADP3208C.pdf
(41 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADP3208CJCPZ-RL
Manufacturer:
AD
Quantity:
4 500
Part Number:
ADP3208CJCPZ-RL
Manufacturer:
ON/安森美
Quantity:
20 000
ADP3208C
General Recommendations
1.
2.
3.
4.
5.
6.
7.
Power Circuitry
1.
For best results, use a PCB of four or more layers. This
should provide the needed versatility for control circuitry
interconnections with optimal placement; power planes for
ground, input, and output; and wide interconnection traces
in the rest of the power delivery current paths. Keep in
mind that each square unit of 1 oz copper trace has a
resistance of ~0.53 mΩ at room temperature.
When high currents must be routed between PCB layers,
vias should be used liberally to create several parallel
current paths so that the resistance and inductance
introduced by these current paths is minimized and the via
current rating is not exceeded.
If critical signal lines (including the output voltage sense
lines of the ADP3208C) must cross through power
circuitry, it is best if a signal ground plane can be
interposed between those signal lines and the traces of the
power circuitry. This serves as a shield to minimize noise
injection into the signals at the expense of increasing signal
ground noise.
An analog ground plane should be used around and under
the ADP3208C for referencing the components associated
with the controller. This plane should be tied to the nearest
ground of the output decoupling capacitor, but should not
be tied to any other power circuitry to prevent power
currents from flowing into the plane.
The components around the ADP3208C should be located
close to the controller with short traces. The most important
traces to keep short and away from other traces are those
to the FB and CSSUM pins. Refer to Figure 36 for more
details on the layout for the CSSUM node.
The output capacitors should be connected as close as
possible to the load (or connector) that receives the power
(for example, a microprocessor core). If the load is distributed,
the capacitors should also be distributed and generally placed
in greater proportion where the load is more dynamic.
Avoid crossing signal lines over the switching power path
loop, as described in the Power Circuitry section.
The switching power path on the PCB should be routed to
encompass the shortest possible length to minimize
radiated switching noise energy (that is, EMI) and
conduction losses in the board. Failure to take proper
precautions often results in EMI problems for the entire PC
system as well as noise-related operational problems in the
Rev. 1 | Page 40 of 41 | www.onsemi.com
2.
3.
4.
Signal Circuitry
1.
2.
3.
power-converter control circuitry. The switching power
path is the loop formed by the current path through the
input capacitors and the power MOSFETs, including all
interconnecting PCB traces and planes. The use of short,
wide interconnection traces is especially critical in this
path for two reasons: it minimizes the inductance in the
switching loop, which can cause high energy ringing, and it
accommodates the high current demand with minimal
voltage loss.
When a power-dissipating component (for example, a
power MOSFET) is soldered to a PCB, the liberal use of
vias, both directly on the mounting pad and immediately
surrounding it, is recommended. Two important reasons
for this are improved current rating through the vias and
improved thermal performance from vias extended to the
opposite side of the PCB, where a plane can more readily
transfer heat to the surrounding air. To achieve optimal
thermal dissipation, mirror the pad configurations used to
heat sink the MOSFETs on the opposite side of the PCB. In
addition, improvements in thermal performance can be
obtained using the largest possible pad area.
The output power path should also be routed to encompass
a short distance. The output power path is formed by the
current path through the inductor, the output capacitors,
and the load.
For best EMI containment, a solid power ground plane
should be used as one of the inner layers and extended
under all power components.
The output voltage is sensed and regulated between the FB
and FBRTN pins, and the traces of these pins should be
connected to the signal ground of the load. To avoid
differential mode noise pickup in the sensed signal, the
loop area should be as small as possible. Therefore, the FB
and FBRTN traces should be routed adjacent to each other,
atop the power ground plane, and back to the controller.
The feedback traces from the switch nodes should be
connected as close as possible to the inductor. The CSREF
signal should be Kelvin connected to the center point of
the copper bar, which is the V
inductors of all the phases.
On the back of the ADP3208C package, there is a metal
pad that can be used to heat sink the device. Therefore,
running vias under the ADP3208C is not recommended
because the metal pad may cause shorting between vias.
CORE
common node for the