HMP8190CN Intersil Corporation, HMP8190CN Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
HMP8190CN
Manufacturer Part Number
HMP8190CN
Description
NTSC/PAL Video Encoder
Manufacturer
Intersil Corporation
Datasheet
1.HMP8190CN.pdf
(32 pages)
Typical Performance Curves
Application Information
PCB Considerations
A PCB board with a minimum of 4 layers is recommended,
with layers 1 and 4 (top and bottom) for signals and internal
layers 2 and 3 for power and ground. The PCB layout should
implement the lowest possible noise on the power and
ground planes by providing excellent decoupling. PCB trace
lengths between groups of VAA and GND pins should be as
short as possible.
Component Placement
The optimum layout places the HMP8190/HMP8191 at the
edge of the PCB and as close as possible to the video output
connector. External components should be positioned as
close as possible to the appropriate pin, ideally such that
traces can be connected point to point. Chip capacitors are
recommended where possible, with radial lead ceramic
capacitors the second-best choice.
Traces containing digital signals should not be routed over,
under, or adjacent to the analog output traces to minimize
crosstalk. If this is not possible, coupling can be minimized
by routing the digital signals at a 90 degree angle to the
analog signals. The analog output traces should also not
cross over or under the V
frequency power supply rejection.
Power and Ground Planes
A common ground plane for all devices, including the
HMP8190/HMP8191, is recommended. However, placing the
encoder on an electrically connected GND peninsula reduces
noise levels. All GND pins on the HMP8190/HMP8191 must
be connected to the ground plane. Typical power and ground
planes are shown in Figure 26.
FIGURE 24. H SYNC JITTER IN A FRAME (PAL)
CC
29
power plane to maximize high-
(Continued)
HMP8190, HMP8191
The small connection between the ground areas should be
made wide enough so that most of the encoders digital inputs
can be routed over or under it. It is especially important that
the CLK and CLK2 signals cross through the connection.
The HMP8190/HMP8191 should have its own power plane
that is isolated from the common power plane of the board,
with a gap between the two power planes of at least 1/8 inch.
All V
to this isolated power plane.
The HMP8190/HMP8191 power plane should be connected
to the board’s normal V
though a low-resistance ferrite bead, such as a Ferroxcube
5659065-3B, Fair-Rite 2743001111, or TDK BF45-4001. The
ferrite bead provides resistance to switching currents,
improving the performance of HMP8190/HMP8191. A single,
large capacitor should also be used between the
HMP8190/HMP8191 power plane and the ground plane to
control low-frequency power supply ripple.
For proper operation, power supply decoupling is required. It
should be done using a 0.1 F ceramic capacitor in parallel
with a 0.01 F chip capacitor for each group of V
ground. These capacitors should be located as close to the
V
If a separate linear regulator is used to provide power to the
HMP8190/HMP8191 power plane, the power-up sequence
should be designed to ensure latchup will not occur. A
separate linear regulator is recommended if the power
supply noise on the V
the noise (that is less than 1MHz) on the V
onto the analog outputs.
AA
AA
and GND pins as possible, using short, wide traces.
pins of the HMP8190/HMP8191 must be connected
FIGURE 25. SCH PHASE MEASUREMENT
AA
CC
pins exceeds 200mV. About 10% of
power plane at a single point
AA
pins will couple
AA
pins to