DS4000 Dallas Semiconducotr, DS4000 Datasheet
DS4000
Available stocks
Related parts for DS4000
DS4000 Summary of contents
Page 1
... GENERAL DESCRIPTION The DS4000 digitally controlled temperature-compen- sated crystal oscillator (DC-TCXO) features a digital temperature sensor, one fixed-frequency temperature- compensated square-wave programmable temperature-compensated wave output (F ), and digital communication for 2 frequency tuning (SDA, SCL). APPLICATIONS Reference Oscillators in PLL Circuits Global Positioning Systems ...
Page 2
ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground Storage Temperature Range Operating Voltage Range Operating Temperature Range Commercial Industrial Soldering Temperature Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These ...
Page 3
AC ELECTRICAL CHARACTERISTICS: TCXO ( ±5%, over the operating temperature range.) CC PARAMETER Output Frequency Frequency Stability vs. Temperature Frequency Stability vs. Voltage Frequency Stability vs. Aging Rise and Fall Time, 10 ...
Page 4
AC ELECTRICAL CHARACTERISTICS—2-WIRE SERIAL INTERFACE (V = 4.75 to 5.25V -40°C to +85° PARAMETER SYMBOL SCL Clock Frequency Bus Free Time Between a STOP and START Condition Hold Time (Repeated) t START Condition Low Period of ...
Page 5
Figure 1. Timing Diagram PIN DESCRIPTION PIN NAME 1A, 1B, 1C, GND Ground. DC power is provided to the device on these pins. 1D, 2C, 2D 2A, 2B N.C. No Connection. (Do not connect to ground.) 3A, 3B GND Oscillator ...
Page 6
... DETAILED DESCRIPTION The DS4000 digitally controlled temperature-compensated crystal oscillator (DC-TCXO) features a digital temperature sensor, one fixed-frequency temperature-compensated square-wave output (F temperature-compensated square-wave output (F Figure 2. Block Diagram SDA SCL A0 ), and digital communication for frequency tuning (SDA, SCL 2-WIRE SERIAL INTERFACE DS4000 ...
Page 7
... TEMPERATURE-COMPENSATED CRYSTAL OSCILLATOR The DS4000 can either function as a standalone TCXO digitally controlled TCXO. When used as a standalone TCXO, the only requirements needed to function properly are power, ground, and an output. However, the 2-wire interface must be used to tune (push and pull) the crystal. ...
Page 8
DIGITAL TUNING THE BASE CRYSTAL FREQUENCY When using the 2-wire interface for tuning the base frequency, the frequency tuning register is used. The frequency tuning register contains two’s complement data. The data is used to add or subtract an offset ...
Page 9
... The digital temperature sensor provides 10-bit temperature readings that indicate the temperature of the device. Temperature readings are communicated from the DS4000 over a 2-wire serial interface. No additional components are required. The DS4000 has an external address bit that allows a user to choose the slave address from two possible values. ...
Page 10
READ TEMPERATURE COMMAND This command reads the last temperature conversion result from the temperature register in the format described in the Reading Temperature section application can accept temperature resolutions of +1.0°C, then the master can read the first ...
Page 11
... START and STOP conditions. The DS4000 operates as a slave on the 2-wire bus. The DS4000 works in a regular mode (100kHz clock rate) and a fast mode (400kHz clock rate), which are defined within the bus specifications. ...
Page 12
Figure 3. Data Transfer On 2-Wire Serial Bus SDA MSB SLAVE ADDRESS SCL 1 2 START CONDITION DATA TRANSFER Figures 4 and 5 detail how data transfer is accomplished on the 2-wire bus. Depending on the R/ W bit in ...
Page 13
... SLAVE ADDRESS The slave address is the first byte received following the START condition generated by the master device. The address byte consists of a 7-bit slave address and the R/ W direction bit. The DS4000 slave address is set to 100010A , where A is externally hardwired to a HIGH or LOW state. This allows design flexibility to set the slave’s ...
Page 14
... DS4000KI/WBGA 0°C to +70°C DS4000KIN/WBGA -40°C to +85°C PIN-PACKAGE TOP MARK 24 BGA DS4000A0 DS4000A0 24 BGA ### BGA DS4000CW DS4000CW 24 BGA ### BGA DS4000D0 DS4000D0 24 BGA ### BGA DS4000EC DS4000EC 24 BGA ### BGA DS4000G0 DS4000G0 24 BGA ### BGA DS4000GF DS4000GF 24 BGA ### BGA ...
Page 15
PACKAGE INFORMATION (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/DallasPackInfo.) NOTE: THE BGA IS SOLDER-MASKED DEFINED ...
Page 16
PACKAGE INFORMATION (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/DallasPackInfo.) PAD: 0.85mm SOLDERMASK: 0.60mm Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry ...