LTC1592 Linear Integrated Systems, LTC1592 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
LTC1592
Manufacturer Part Number
LTC1592
Description
(LTC1588 - LTC1592) 12-/14-/16-Bit SoftSpan DACs
Manufacturer
Linear Integrated Systems
Datasheet
1.LTC1592.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC1592ACG
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC1592ACG
Manufacturer:
LT/凌特
Quantity:
20 000
Company:
Part Number:
LTC1592ACG#PBF
Manufacturer:
LTC
Quantity:
119
Company:
Part Number:
LTC1592AIG
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC1592BCG
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC1592BCG
Manufacturer:
LT/凌特
Quantity:
20 000
Company:
Part Number:
LTC1592BCG#PBF
Manufacturer:
LT
Quantity:
77
www.DataSheet4U.com
INPUT WORD (LTC1592)
OPERATIO
INPUT WORD (LTC1588)
INPUT WORD (LTC1589)
Serial Interface
When the CS/LD is brought to a logic low, the data on the
SDI input is loaded into the shift register on the rising edge
of the clock. A 4-bit command word (C3 C2 C1 C0),
followed by four “don’t care” bits and 16 data bits
(MSB-first) is the minimum loading sequence required for
the LTC1588/LTC1589/LTC1592. When the CS/LD is
brought to a logic high, the clock is disabled internally and
the command word is executed.
If no daisy-chaining is required, the input stream can be
24-bit wide as shown in Figure 1a. The first four bits are the
command word, followed by four “don’t care” bits, then a
16-bit data word. The last four bits (LSBs) of this 16-bit
data word are don’t cares for the LTC1588. For the
LTC1589, the last 2 bits of the 16-bit data word are don’t
cares.
If daisy-chaining is required or the input needs to be
written in two 16-bit wide segments, then the input stream
must be 32-bit wide and the first 8 bits loaded are “don’t
care” bits. The remaining bits work the same as a 24-bit
stream which is described in the previous paragraph. The
output of the internal 32-bit shift register is available on the
SDO pin 32 clock cycles later.
Multiple LTC1588/LTC1589/LTC1592s may be daisy-
chained together by connecting the SDO pin to the SDI pin
of the next IC. The clock and CS/LD signals should remain
common to all ICs in the daisy-chain. The serial data is
C3
C3
C3
COMMAND
COMMAND
COMMAND
C2
C2
C2
C1 C0
C1 C0
C1 C0
U
X
X
X
DON’T CARE
DON’T CARE
DON’T CARE
X
X
X
X
X
X
X
X
X
MSB
MSB
MSB
D15
D11 D10 D9 D8 D7 D6 D5 D4 D3 D2
D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2
D14
D13
D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2
DATA (12 BITS + 4 DON’T-CARE BITS)
DATA (14 BITS + 2 DON’T-CARE BITS)
clocked to all ICs, then the CS/LD signal is pulled high to
update all of them simultaneously.
Power-On Reset and Clear
When the power supply is first turned on, the LTC1588/
LTC1589/LTC1592 will power up in 5V unipolar mode (C3
C2 C1 C0 = 1000). All the internal registers are set to zeros
and the DAC is set to zero code.
The LTC1588/LTC1589/LTC1592 must first be pro-
grammed in either unipolar or bipolar mode. There are six
operating modes available and can be software-pro-
grammed by the command word. When a CLR signal is
brought to low, it clears all internal registers to zero. The
DAC output voltage goes to zero volts. If an update DAC
command (C3 C2 C1 C0 = 0001) is issued immediately
after the CLR signal, the DAC output remains at zero volts.
If a CLR signal is given within a 100ns interval immediately
after CS/LD goes high, the user should reload the output
range.
Output Range Programming
There are two output ranges available in unipolar mode
and four output ranges available in bipolar mode. See
Function Table for details. All output ranges are with re-
spect to a 5V reference input. When changing the LTC1588/
LTC1589/LTC1592 to a new mode, the command word
and data are given at the same time (24 or 32 bit). When
LTC1588/LTC1589/LTC1592
DATA (16 BITS)
D1 D0
LSB
D1 D0
X
LSB
X
D1 D0
X
X
1588992 TD2
1588992 TD4
1588992 TD3
LSB
X
X
1588992fa
9