SC16C2550 Philips Semiconductors, SC16C2550 Datasheet - Page 8

• Manufacturer Part Number: SC16C2550
• Description: Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder
• Manufacturer: Philips Semiconductors

Philips Semiconductors
Table 2:
9397 750 11621
Product data
Symbol
XTAL2
CDA,
CDB
CTSA,
CTSB
DSRA,
DSRB
DTRA,
DTRB
RIA, RIB
RTSA,
RTSB
RXA, RXB 10, 9
TXA, TXB 11, 12 13, 14
Pin description
17
38, 19 42, 21
36, 25 40, 28
37, 22 41, 25
33, 34 37, 38
39, 23 43, 26
32, 24 36, 27
DIP40 PLCC44 LQFP48
19
11, 10
Pin
…continued
14
40, 16
38, 23
39, 20
34, 35
41, 21
33, 22
5, 4
7, 8
Type Description
O
I
I
I
O
I
O
I
O
Dual UART with 16 bytes of transmit and receive FIFOs and IrDA
Output of the crystal oscillator or buffered clock. (See also XTAL1.)
Crystal oscillator output or buffered clock output. Should be left open if an
external clock is connected to XTAL1. For extended frequency operation,
this pin should be tied to V
Carrier Detect (Active-LOW). These inputs are associated with individual
UART channels A through B. A logic 0 on this pin indicates that a carrier
has been detected by the modem for that channel.
Clear to Send (Active-LOW). These inputs are associated with individual
UART channels, A through B. A logic 0 on the CTS pin indicates the
modem or data set is ready to accept transmit data from the SC16C2550.
Status can be tested by reading MSR[4]. This pin has no effect on the
UART’s transmit or receive operation.
Data Set Ready (Active-LOW). These inputs are associated with
individual UART channels, A through B. A logic 0 on this pin indicates the
modem or data set is powered-on and is ready for data exchange with the
UART. This pin has no effect on the UART’s transmit or receive operation.
Data Terminal REady (Active-LOW). These outputs are associated with
individual UART channels, A through B. A logic 0 on this pin indicates that
the SC16C2550 is powered-on and ready. This pin can be controlled via
the modem control register. Writing a logic 1 to MCR[0] will set the DTR
output to logic 0, enabling the modem. This pin will be a logic 1 after writing
a logic 0 to MCR[0], or after a reset. This pin has no effect on the UART’s
transmit or receive operation.
Ring Indicator (Active-LOW). These inputs are associated with individual
UART channels, A through B. A logic 0 on this pin indicates the modem has
received a ringing signal from the telephone line. A logic 1 transition on this
input pin will generate an interrupt.
Request to Send (Active-LOW). These outputs are associated with
individual UART channels, A through B. A logic 0 on the RTS pin indicates
the transmitter has data ready and waiting to send. Writing a logic 1 in the
modem control register MCR[1] will set this pin to a logic 0, indicating data
is available. After a reset this pin will be set to a logic 1. This pin has no
effect on the UART’s transmit or receive operation.
Receive data A, B. These inputs are associated with individual serial
channel data to the SC16C2550 receive input circuits, A-B. The RX signal
will be a logic 1 during reset, idle (no data), or when the transmitter is
disabled. During the local loop-back mode, the RX input pin is disabled and
TX data is connected to the UART RX input, internally.
Transmit data A, B. These outputs are associated with individual serial
transmit channel data from the SC16C2550. The TX signal will be a logic 1
during reset, idle (no data), or when the transmitter is disabled. During the
local loop-back mode, the TX output pin is disabled and TX data is
internally connected to the UART RX input.
Rev. 03 — 19 June 2003
CC
via a 2 k resistor.
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
SC16C2550
encoder/decoder
8 of 46