MBM29SL160BD Fujitsu Media Devices, MBM29SL160BD Datasheet - Page 21
![no-image](/images/no-image-200.jpg)
MBM29SL160BD
Manufacturer Part Number
MBM29SL160BD
Description
16M (2M x 8/1M x 16) BIT
Manufacturer
Fujitsu Media Devices
Datasheet
1.MBM29SL160BD.pdf
(61 pages)
Erase Suspend/Resume
complete. (Refer to the Write Operation Status section for Sector Erase Timer operation.) Loading the sector
erase buffer may be done in any sequence and with any number of sectors (0 to 38).
Sector erase does not require the user to program the devices prior to erase. The devices automatically program
all memory locations in the sector(s) to be erased prior to electrical erase (Preprogram function). When erasing
a sector or sectors the remaining unselected sectors are not affected. The system is not required to provide any
controls or timings during these operations.
The system can determine the status of the erase operation by using DQ
RY/BY.
The sector erase begins after the 50µs time out from the rising edge of CE or WE whichever happens first for
the last sector erase command pulse and terminates when the data on DQ
section.) at which time the devices return to the read mode. Data polling and Toggle Bit must be performed at
an address within any of the sectors being erased.
Multiple Sector Erase Time; [Sector Erase Time + Sector Program Time (Preprogramming)] Number of Sector
Erase
Figure 22 illustrates the Embedded Erase
The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads
from or programs to a sector not being erased. This command is applicable ONLY during the Sector Erase
operation which includes the time-out period for sector erase. The Erase Suspend command will be ignored if
written during the Chip Erase operation or Embedded Program Algorithm. Writting the Erase Suspend command
(B0H) during the Sector Erase time-out results in immediate termination of the time-out period and suspension
of the erase operation.
Writing the Erase Resume command (30H) resumes the erase operation. The address are DON’T CARES when
writing the Erase Suspend or Erase Resume command (30H).
When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum
of 20µs to suspend the erase operation. When the devices have entered the erase-suspended mode, the
RY/BY output pin will be at Hi-Z and the DQ
use the address of the erasing sector for reading DQ
suspended. Further writes of the Erase Suspend command are ignored.
When the erase operation has been suspended, the devices default to the erase-suspend-read mode. Reading
data in this mode is the same as reading from the standard read mode except that the data must be read from
sectors that have not been erase-suspended. Successively reading from the erase-suspended sector while the
device is in the erase-suspend-read mode will cause DQ
After entering the erase-suspend-read mode, the user can program the device by writing the appropriate
command sequence for Program. This program mode is known as the erase-suspend-program mode. Again,
programming in this mode is the same as programming in the regular Program mode except that the data must
be programmed to sectors that are not erase-suspended. Successively reading from the erase-suspended sector
while the devices are in the erase-suspend-program mode will cause DQ
suspended Program operation is detected by the RY/BY output pin, Data polling of DQ
(DQ
while DQ
To resume the operation of Sector Erase, the Resume command (30H) should be written. Any further writes of
the Resume command at this point will be ignored. Another Erase Suspend command can be written after the
chip has resumed erasing.
6
) which is the same as the regular Program operation. Note that DQ
6
can be read from any address.
MBM29SL160TD
TM
7
Algorithm using typical command strings and bus operations.
bit will be at logic “1”, and DQ
6
and DQ
2
to toggle. (See the section on DQ
-10/-12
7
to determine if the erase operation has been
/MBM29SL160BD
7
must be read from the Program address
2
7
7
to toggle. The end of the erase-
(Data Polling), DQ
6
is “1” (See Write Operation Status
will stop toggling. The user must
7
or by the Toggle Bit I
2
.)
6
(Toggle Bit), or
-10/-12
21