st72321j STMicroelectronics, st72321j Datasheet - Page 101
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
st72321j
Manufacturer Part Number
st72321j
Description
8-bit Mcu With Nested Interrupts, Flash, 10-bit Adc, 5 Timers, Spi, Sci, I2c Interface
Manufacturer
STMicroelectronics
Datasheet
1.ST72321J.pdf
(179 pages)
- Current page: 101 of 179
- Download datasheet (2Mb)
SERIAL COMMUNICATIONS INTERFACE (Cont’d)
10.6.4.3 Receiver
The SCI can receive data words of either 8 or 9
bits. When the M bit is set, word length is 9 bits
and the MSB is stored in the R8 bit in the SCICR1
register.
Character reception
During a SCI reception, data shifts in least signifi-
cant bit first through the RDI pin. In this mode, the
SCIDR register consists or a buffer (RDR) be-
tween the internal bus and the received shift regis-
ter (see
Procedure
– Select the M bit to define the word length.
– Select the desired baud rate using the SCIBRR
– Set the RE bit, this enables the receiver which
When a character is received:
– The RDRF bit is set. It indicates that the content
– An interrupt is generated if the RIE bit is set and
– The error flags can be set if a frame error, noise
Clearing the RDRF bit is performed by the following
software sequence done by:
1. An access to the SCISR register
2. A read to the SCIDR register.
The RDRF bit must be cleared before the end of the
reception of the next character to avoid an overrun
error.
Break Character
When a break character is received, the SPI han-
dles it as a framing error.
Idle Character
When a idle frame is detected, there is the same
procedure as a data received character plus an in-
terrupt if the ILIE bit is set and the I bit is cleared in
the CCR register.
and the SCIERPR registers.
begins searching for a start bit.
of the shift register is transferred to the RDR.
the I bit is cleared in the CCR register.
or an overrun error has been detected during re-
ception.
Figure
58).
Overrun Error
An overrun error occurs when a character is re-
ceived when RDRF has not been reset. Data can
not be transferred from the shift register to the
RDR register as long as the RDRF bit is not
cleared.
When a overrun error occurs:
– The OR bit is set.
– The RDR content will not be lost.
– The shift register will be overwritten.
– An interrupt is generated if the RIE bit is set and
The OR bit is reset by an access to the SCISR reg-
ister followed by a SCIDR register read operation.
Noise Error
Oversampling techniques are used for data recov-
ery by discriminating between valid incoming data
and noise.
When noise is detected in a frame:
– The NF is set at the rising edge of the RDRF bit.
– Data is transferred from the Shift register to the
– No interrupt is generated. However this bit rises
The NF bit is reset by a SCISR register read oper-
ation followed by a SCIDR register read operation.
Framing Error
A framing error is detected when:
– The stop bit is not recognized on reception at the
– A break is received.
When the framing error is detected:
– the FE bit is set by hardware
– Data is transferred from the Shift register to the
– No interrupt is generated. However this bit rises
The FE bit is reset by a SCISR register read oper-
ation followed by a SCIDR register read operation.
the I bit is cleared in the CCR register.
SCIDR register.
at the same time as the RDRF bit which itself
generates an interrupt.
expected time, following either a de-synchroni-
zation or excessive noise.
SCIDR register.
at the same time as the RDRF bit which itself
generates an interrupt.
ST72321J
101/179
Related parts for st72321j
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ST7-DVP3](/images/no-image3.png)
Part Number:
Description:
Low Cost, Real Time Emulator Series for ST7
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
![ST7-EMU3](/images/no-image3.png)
Part Number:
Description:
Full-featured, real time emulator series for ST7
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
![ST7-88](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![ST7-STICK](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
In-Circuit Programmer
Manufacturer:
STMicroelectronics
Datasheet:
![st7-56](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-40](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-48](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-30](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-34](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-36](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-28](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-24](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-20](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-16](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet:
![st7-10](/images/no-image3.png)
Part Number:
Description:
Power Transformer
Manufacturer:
Superworld Electronics
Datasheet: