isl3873 Intersil Corporation, isl3873 Datasheet - Page 15

• Manufacturer Part Number: isl3873
• Description: Wireless Lan Integrated Medium Access Controller With Baseband Processor
• Manufacturer: Intersil Corporation

USB Port
The USB interface implemented in the ISL3873 complies
with the Universal Serial Bus Specification Revision 1.1.
dated September 23, 1998, which is available from the USB
Implementers’ Forum at http://www.usb.org/.
The USB supports 4 endpoints.
• One Communications Class control endpoint for interface
• One Communications Class interrupt endpoint for
• Two Bulk endpoints for transfer of encapsulated NDIS
The USB along with USB support firmware provides an
alternate host interface for attaching an 802.11{b} WLAN
adapter to a host computer. This interface does not provide
“wireless USB” where USB packets are sent on the wireless
medium due to timing constraints in the USB protocol.
USB+ and USB- are the differential pair signals provided for
the user. These signals are capable of directly driving a USB
cable.
USB_DETECT is a 5V tolerant input to the ISL3873 device.
It is used to signal the MAC processor that a USB cable is
attached to the unit.
Complete details on the USB firmware for controlling this
port can be obtained by contacting the factory directly.
Power Sequencing
The ISL3873 provides a number of firmware controlled port
pins that are used for controlling the power sequencing and
other functions in the front end components of the radio.
Packet transmission requires precise control of the radio.
Ideally, energy at the antenna ceases after the last symbol of
information has been transmitted. Additionally, the
management;
signalling interrupts to the host; and,
functions to and from the host.
DEALLOCATE
HOST
ALLOCATE/
BUS
REQUEST
15
OFFSET CENTER
POST-WRITE
FID
DATA PORT
PRE-READ/
FIGURE 9. BLOCK DIAGRAM OF A BUFFER ACCESS PATH
BUFFER DESCRIPTOR
ACCESS (FIRMWARE)
OFFSET
BLOCK
ISL3873
A
D
transmit/receive switch must be controlled properly to protect
the receiver. It's also important to apply appropriate
modulation to the PA while it's active.
Signaling sequences for the beginning and end of normal
transmissions are illustrated in Figure 10. Table 1 lists
applicable delays associated with these control signals.
A transmission begins with PE2 as shown in Figure 10. Next,
the transmit/receive switch is configured for transmission via
the differential pair TR_SW and TR_SW_BAR. This is
followed by a transmit enable (TX_ENABLE) to the
Baseband processor inside the ISL3873. This enable
activates the transmit state machine in the BBP. Lastly,
PA_PE activates the PA. Delays for these signals related to
the initiation of transmission are referenced to PE2.
Immediately after the final data bit has been clocked out of the
MAC the Baseband processor is disabled. The MAC then waits
for a control signal (TX_READY) from the Baseband processor
to go inactive, signaling that the BBP has modulated the final
information-rich symbol. It then immediately de-asserts PA_PE
followed by placing the transmit/receive switch in the receive
position and ending with PE2 going high. Delays for these
signals related to the termination of transmission are
referenced to the rising edge of PE2
PE1 and PE2 encoding details are found in Table 2.
Note that during normal receive and transmit operation that
PE1 is static and PE2 toggles for receive and transmit
states.
PE2 to TR Switch
PE2 to PA_PE
PA_PE to PE2
TR Switch to PE2
TABLE 1. TRANSMIT CONTROL TIMING SPECIFICATIONS
FRAME BUFFER
PARAMETER
VIRTUAL
HEADER
STATUS
DATA
SYMBOL DELAY
t
t
t
t
D1
D3
D4
D5
MEMORY
BUFFER
2
3
3
2
.
TOLERANCE UNITS
0.1
0.1
0.1
0.1
s
s
s
s