rsa6351p Yamatake Corporation, rsa6351p Datasheet - Page 2

• Manufacturer Part Number: rsa6351p
• Description: Single Loop Controller
• Manufacturer: Yamatake Corporation

I Specifications
PV input
Motor feedback Allowable resistance
potentiometer
input (RI model)
RSP input
Indications
and setting
Control output Output type
Input type
Input sampling time
Input impedance
Input bias
Input bias current
Burnout indication
Allowable input current
Allowable input voltage DC current input: Max. 4V (a higher voltage might cause device failure)
Cold junction
compensation
accuracy
Cold junction
compensation method
Burnout detection
Input type
Scaling
Sampling cycle
Input impedance
Input bias current
Burnout indication
Allowable input current
Allowable input voltage DC current input: Max. 4V (a higher voltage might cause device failure)
PV, SP indication method 4-digit, 7-segment LED (PV: Upper green display, SP: Lower orange display)
Number of setting points Max. 8 points
Setting range
Multi-status indicator
Indication accuracy
Indication range
Control action
Number of PID groups Max. 8 groups
PID auto-tuning
Output rating
Cycle time (s)
PID control
Just-FiTTER
ON/OFF control
Control operation selection Direct action or reverse action
Heat/Cool control selection Control output and event output (When the control output is a motor drive relay output, the heat/cool control
100ms
Multi-range of inputs - thermocouple, RTD, DC current and DC voltage
DC voltage input: Min. 1MΩ, DC current input: Max. 100Ω
-1999 to +9999 or -199.9 to +999.9
Thermocouple input:
RTD input:
DC voltage input:
Thermocouple input:
RTD input:
DC voltage input:
DC current input:
DC current input: Max. 30mA
±0.5°C (at an ambient temperature of 23±2°C )
±1.0°C (at an ambient temperature of 15 to 35°C )
±1.5°C (at an ambient temperature of 0 to 15°C or 35 to 50°C)
Compensation inside or outside (only at 0°C) the measuring instrument can be selected.
100 to 2500Ω
AL07 indication
Linear 0 to 2-0mA/4 to 20mA or linear 0 to 5V/1 to 5V/0 to 10V
Possible in a range of -1999 to +9999. It is also possible to set the decimal point position.
100ms
DC voltage input: Min. 1MΩ, DC current input: Max/ 100Ω
DC voltage input: 0 to 5V, 1 to 5V range. Max. 3µA
DC voltage input: Downscale +AL06
DC current input: Down scale + AL06 (However, the burnout cannot be detected in a range of 0 to 20mA)
DC current input: Max. 30mA
Lower to higher limit value of the PV range (Restriction by SP lower limit to upper limit possible)
The control output status, alarm or RUN/READY status is indicated.
±0.1%FS±1 digit
In the negative area of the thermocouple, the accuracy is ±0.2%FS±1 digit (at an ambient temperature of 23±2°C.)
See Table 1.
Automatic PID value setting by limit cycle method.
However, one of the following 3 control characteristics can be selected:
• Standard
• Quick disturbance response
• Less up/down fluctuations
Control output: 1
Control output: 2
Service life:
Min. opening/closing time:
Proportional band (%FS)
Integral time (s)
Derivative time (s)
Manual set (%)
Overshoot suppression coefficient
Operating differential (°C)
is disabled.)
Time proportional PID Position proportional PID Time proportional PID
NO side: 250Vac/30Vdc,
3A (resistive load)
NC side: 250Vac/30Vdc, Service life: 120,000
1A (resistive load)
NO side: 50,000 cycles
NC side: 100,000 cycles
250ms
or more
or more
Relay contact
5 to 120
0 to 10V range
Motor drive relay output Voltage pulse output
Contact rating: 250Vac
tions: 24Vdc, 40mA
Contact type: 1c
Min. switching specifica-
+1mA typical
0 to 5V, 1 to 5V range... 3.5µA or less
0 to 10V range... 7µA or less
(However, the burnout cannot be detected
Downscale + AL02
(However, the burnout cannot be detected
+0.2µA or less
1V range or less... 1µA or less
Upscale + AL01
Upscale + alarm display (Note 1)
Downscale + AL02
for the 0 to 10V range.)
for the 0 to 20mA range.)
2-circuit
8A (resistive load)
cycles or more
—
-10.0 to +110.0
0 to 100
0 to 9999 or 0.0 to 999.9
0.1 to 999.9
0 to 9999 or 0.0 to 999.9
0 to 9999 or 0.0 to 999.9
2
Max. 5µA
0.1, 0.25, 0.5, 1 to 20
Open terminal voltage:
Internal resistance:
Allowable current:
Min. OFF/ON time:
When 10s or less: 1ms
When 10s or longer:
19Vdc ± 15%
82Ω ± 0.5%
Max. 24mAdc
250ms
Output resolution: 1/10000 Output resolution: 1/10000
Allowable load resistance: Allowable load resistance:
Output accuracy: ±0.1%FS Output accuracy: ±0.1%FS
Output type: 0 to 20mAdc Output type: 0 to 5Vdc/
or 4 to 20mAdc
Max. 600Ω
(However, ±1%FS for
0 to 1mA)
Continuous PID
Current output
(Note 1)
RTD or A-wire burnout:
B-wire or C-wire burnout:
More than 2-wire burnout:
—
Upscale + AL01
Upscale + AL01, AL03
Upscale + AL01, AL03
Continuous voltage output
1 to 5Vdc or 0 to 10Vdc
Min. 1000Ω
(However, ±1%FS for
0 to 0.05V)
Continuous PID
—