rsa6351p Yamatake Corporation, rsa6351p Datasheet - Page 3

• Manufacturer Part Number: rsa6351p
• Description: Single Loop Controller
• Manufacturer: Yamatake Corporation

Auxiliary
output
External
contact input Function
(DI)
Event
Output type
Load resistance
Output accuracy
Output resolution
Number of inputs
Input rating
Min. detection holding time 0.2s or longer
Allowable ON contact Max. 250Ω
resistance
Allowable OFF contact Min. 100kΩ
resistance
Allowable ON-state
residual voltage
Open terminal voltage 5.5Vdc±1V
ON terminal current
Number of output points 2 to 3 points (according to a model)
Number of internal
event settings
Event type
G shows that the ON/
OFF is changed at
this value.
shows that the ON/
OFF is changed at
a point that "1U" is
added to this value.
Max. 4 points
Up to 8 kinds of setting value (SP) selections, PID group selection, RUN/READY selection, AUTO/MANUAL
selection, LSP/RSP selection, Auto tuning stop/start, Control action Direct/Reverse selection, SP ramp enable/
disable, PV value hold, Max. PV value hold, Min. PV value hold, Timer start/stop, All DO latch cancellation,
advance operation, step hold
Non-voltage contact or open collector
Max. 1.0V
Approx. 7.5mA (at short-circuit), Approx. 5.0mA (at contact resistance of 250Ω)
Up to 8 settings
Main setting
Main setting
Main setting
ON
ON
ON
SP + Main setting
ON
ON
Main setting
±0.1%FS (However, ±1%FS for 0 to 1mA)
Direct action
Direct action
Direct action
Direct action
Direct action
Direct action
Direct action
HYS
HYS
HYS
HYS
HYS
Main setting
Main setting
CT at output ON
HYS
HYS
Heater burnout/Over-current
0 to 20mAdc or 4 to 20mA
ON
ON
HYS
HYS
HYS
Sub-setting
Sub-setting
Sub-setting
Deviation low limit
PV high/low limit
SP high/low limit
MV
PV
SP
PV
Current output
PV high limit
PV
SP high limit
SP
MV low limit
ON
Max. 600Ω
ON
ON
1/10000
Main setting
SP + Main setting
Main setting
Main setting Sub-setting
ON
HYS
HYS
ON
Main setting Sub-setting
Reverse action
Main setting
Reverse action
Reverse action
Reverse action
Reverse action
Reverse action
Reverse action
HYS
3
HYS
HYS
CT at output ON
ON
ON
ON
HYS
HYS
Main setting
MV
ON
HYS
PV
ON
HYS
HYS
Sub-setting
PV
SP
SP
PV
Main setting
ON
ON
ON
ON
±0.1%FS (However, ±1%FS for 0 to 0.05V)
Main setting Sub-setting
Main setting
SP + Main setting
Main setting
HYS
Direct action
Direct action
Direct action
Direct action
Direct action
Direct action
Direct action
HYS
HYS
HYS
HYS
Main setting
Main setting
CT at output OFF
0 to 5Vdc/1 to 5Vdc or 0 to 10Vdc
SP
HYS
Continuous voltage output
HYS
ON
ON
ON
Deviation high/low limit
HYS
HYS
Sub-setting
Deviation high limit
Heater short-circuit
MV high/low limit
MV
PV
PV
SP
MV
MV high limit
PV
PV low limit
SP low limit
Min. 1000Ω
ON
ON
1/10000
Main setting
Main setting
ON
Main setting Sub-setting
HYS
ON
Main setting Sub-setting
ON
HYS
Reverse action
Reverse action
Reverse action
Reverse action
Reverse action
Reverse action
Reverse action
HYS
CT at output OFF
HYS
ON
ON
SP
HYS
SP + Main setting
HYS
HYS
Main setting
Main setting
SP
ON
PV
HYS
HYS
ON
PV
MV
MV
PV