max98089 Maxim Integrated Products, Inc., max98089 Datasheet - Page 126
![no-image](/images/no-image-200.jpg)
max98089
Manufacturer Part Number
max98089
Description
Low-power, Stereo Audio Codec With Flexsound Technology
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.MAX98089.pdf
(131 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
max98089ETN+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
max98089ETN+T
Manufacturer:
ATMEL
Quantity:
2 100
The MAX98089EWY uses a 63-bump WLP package.
Figure 43 provides an example of how to connect to all
active bumps using 3 layers of the PCB. To ensure unin-
terrupted ground returns, use layer 2 as a connecting
layer between layer 1 and layer 2 and flood the remaining
area with ground.
Figure 43. Suggested Routing for the MAX98089EWY
��������������������������������������������������������������� Maxim Integrated Products 126
Recommended PCB Routing
LAYER 2
LAYER 3
LAYER 1
Low-Power, Stereo Audio Codec
with FlexSound Technology
Proper layout and grounding are essential for optimum
performance. When designing a PCB for the ICs, parti-
tion the circuitry so that the analog sections of the IC are
separated from the digital sections. This ensures that the
analog audio traces are not routed near digital traces.
Use a large continuous ground plane on a dedicated
layer of the PCB to minimize loop areas. Connect AGND,
DGND, HPGND, SPKLGND, and SPKRGND directly to
the ground plane using the shortest trace length possible.
Proper grounding improves audio performance, minimizes
crosstalk between channels, and prevents any digital
noise from coupling into the analog audio signals.
Ground the bypass capacitors on MICBIAS, REG, and
REF directly to the ground plane with minimum trace
length. Also be sure to minimize the path length to
AGND. Bypass AVDD directly to AGND.
Connect all digital I/O termination to the ground plane
with minimum path length to DGND. Bypass DVDD,
DVDDS1, and DVDDS2 directly to DGND.
Place the capacitor between C1P and C1N as close as
possible to the ICs to minimize trace length from C1P to
C1N. Inductance and resistance added between C1P and
C1N reduce the output power of the headphone ampli-
fier. Bypass HPVDD and HPVSS with a capacitor located
close to HPVSS with a short trace length to HPGND. Close
decoupling of HPVSS minimizes supply ripple and maxi-
mizes output power from the headphone amplifier.
HPSNS senses ground noise on the headphone jack and
adds the same noise to the output audio signal, thereby
making the output (headphone output minus ground)
noise free. Connect HPSNS to the headphone jack shield
to ensure accurate pickup of headphone ground noise.
Bypass SPKLVDD and SPKRVDD to SPKLGND and
SPKRGND, respectively, with as little trace length as
possible. Connect SPKLP, SPKLN, SPKRP, and SPKRN
to the stereo speakers using the shortest traces pos-
sible. Reducing trace length minimizes radiated EMI.
Route SPKLP/SPKLN and SPKRP/SPKRN as differential
pairs on the PCB to minimize loop area, thereby the
inductance of the circuit. If filter components are used
on the speaker outputs, be sure to locate them as close
as possible to the IC to ensure maximum effectiveness.
Minimize the trace length from any ground-connected
passive components to SPKLGND and SPKRGND to
further minimize radiated EMI.
Supply Bypassing, Layout, and Grounding
MAX98089