adv7181b Analog Devices, Inc., adv7181b Datasheet - Page 37
![no-image](/images/no-image-200.jpg)
adv7181b
Manufacturer Part Number
adv7181b
Description
Multiformat Sdtv Video Decoder
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADV7181B.pdf
(100 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
adv7181b-SBTZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bBCPCZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bBCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bBSTZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bST
Manufacturer:
ADI/亚德诺
Quantity:
20 000
BL_C_VBI Blank Chroma During VBI, Address 0x04[2]
Setting BL_C_VBI high, the Cr and Cb values of all VBI lines
are blanked. This is done so any data that may arrive during
VBI is not decoded as color and output through Cr and Cb.
As a result, it is possible to send VBI lines into the decoder,
then output them through an encoder again, undistorted.
Without this blanking, any wrongly decoded color is encoded
by the video encoder; therefore, the VBI lines are distorted.
Setting BL_C_VBI to 0 decodes and outputs color during VBI.
Setting BL_C_VBI to 1 (default) blanks Cr and Cb values
during VBI.
RANGE Range Selection, Address 0x04[0]
AV codes (as per ITU-R BT-656, formerly known as CCIR-656)
consist of a fixed header made up of 0xFF and 0x00 values.
These two values are reserved and therefore are not to be used
for active video. Additionally, the ITU specifies that the nomi-
nal range for video should be restricted to values between 16
and 235 for luma and 16 to 240 for chroma.
The RANGE bit allows the user to limit the range of values
output by the ADV7181B to the recommended value range. In
any case, it ensures that the reserved values of 255d (0xFF) and
00d (0x00) are not presented on the output pins unless they are
part of an AV code header.
Table 51. RANGE Function
RANGE
0
1 (default)
AUTO_PDC_EN Automatic Programmed Delay Control,
Address 0x27[6]
Enabling the AUTO_PDC_EN function activates a function
within the ADV7181B that automatically programs the
LTA[1:0] and CTA[2:0] to have the chroma and luma data
match delays for all modes of operation. If set, manual registers
LTA[1:0] and CTA[2:0] are not used. If the automatic mode is
disabled (via setting the AUTO_PDC_EN bit to 0), the values
programmed into LTA[1:0] and CTA[2:0] registers become
active.
When AUTO_PDC_EN is 0, the ADV7181B uses the LTA[1:0]
and CTA[2:0] values for delaying luma and chroma samples.
Refer to the LTA[1:0] Luma Timing Adjust, Address 0x27[1:0]
and the CTA[2:0] Chroma Timing Adjust, Address 0x27[5:3]
sections.
When AUTO_PDC_EN is 1 (default), the ADV7181B
automatically determines the LTA and CTA values to have luma
and chroma aligned at the output.
16 ≤ Y ≤ 235
1 ≤ Y ≤ 254
Description
16 ≤ C/P ≤ 240
1 ≤ C/P ≤ 254
Rev. B | Page 37 of 100
LTA[1:0] Luma Timing Adjust, Address 0x27[1:0]
The luma timing adjust register allows the user to specify a
timing difference between chroma and luma samples.
There is a certain functionality overlap with the CTA[2:0]
register. For manual programming, use the following defaults:
•
•
•
Table 52. LTA Function
LTA[1:0]
00 (default)
01
10
11
CTA[2:0] Chroma Timing Adjust, Address 0x27[5:3]
The chroma timing adjust register allows the user to specify a
timing difference between chroma and luma samples. This can
be used to compensate for external filter group delay differences
in the luma vs. chroma path, and to allow a different number of
pipeline delays while processing the video downstream. Review
this functionality together with the LTA[1:0] register.
The chroma can be delayed/advanced only in chroma pixel
steps. One chroma pixel step is equal to two luma pixels. The
programmable delay occurs after demodulation, where one can
no longer delay by luma pixel steps.
For manual programming, use the following defaults:
•
•
•
Table 53. CTA Function
CTA[2:0]
000
001
010
011 (default)
100
101
110
111
CVBS input LTA[1:0] = 00
YC input LTA[1:0] = 01
YPrPb input LTA[1:0] =01
CVBS input CTA[2:0] = 011
YC input CTA[2:0] = 101
YPrPb input CTA[2:0] =110
Description
No delay
Luma 1 clk (37 ns) delayed
Luma 2 clk (74 ns) early
Luma 1 clk (37 ns) early
Description
Not used
Chroma + 2 chroma pixel (early)
Chroma + 1 chroma pixel (early)
No delay
Chroma – 1 chroma pixel (late)
Chroma – 2 chroma pixel (late)
Chroma – 3 chroma pixel (late)
Not used
ADV7181B