lan8720 Standard Microsystems Corp., lan8720 Datasheet - Page 32

no-image

lan8720

Manufacturer Part Number
lan8720
Description
Small Footprint Rmii 10/100 Ethernet Transceiver With Hp Auto-mdix Support
Manufacturer
Standard Microsystems Corp.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lan8720A
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
lan8720A-CP
Manufacturer:
Standard
Quantity:
2 152
Part Number:
lan8720A-CP-ABC
Manufacturer:
SMSC
Quantity:
1 000
Part Number:
lan8720A-CP-TR
Manufacturer:
MORNSUN
Quantity:
1 000
Part Number:
lan8720A-CP-TR
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan8720A-CP-TR
0
Part Number:
lan8720A-CP-TR-ABC
0
Part Number:
lan8720AI
Quantity:
10 000
Part Number:
lan8720AI-CP
Manufacturer:
Standard
Quantity:
5 016
Part Number:
lan8720AI-CP
Manufacturer:
VISHAY
Quantity:
14 585
Part Number:
lan8720AI-CP
Manufacturer:
SMSC
Quantity:
1 000
Part Number:
lan8720AI-CP
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan8720AI-CP-ABC
0
Part Number:
lan8720AI-CP-TR
0
Company:
Part Number:
lan8720AI-CP-TR
Quantity:
7 070
Part Number:
lan8720AI-CP-TR-ABC
0
Revision 1.0 (04-15-09)
4.10
LED2/nINTSEL = 0
LED2/nINTSEL = 1
POLARITY
The LED2/nINTSEL pin is used to select between one of two available modes: REF_CLK In Mode
and REF_CLK Out Mode. The configured mode determines the function of the nINT/REFCLK0 pin.
When configured for REF_CLK Out Mode, the LAN8720 generates the 50MHz RMII REF_CLK and
the interrupt is not available in this mode.
The nINTSEL pin is shared with the LED2 pin. The LED2 output will automatically change polarity
based on the presence of an external pull-down resistor. If the LED pin is pulled high (by the internal
pull-up resistor) to select a logical high for nINTSEL, then the LED output will be active low. If the LED
pin is pulled low by an external pull-down resistor to select a logical low nINTSEL, the LED output will
then be an active high output.
To set nINTSEL without LEDs, float the pin to set nINTSEL high or pull-down the pin with an external
resistor to GND to set nINTSEL low. See
The LED2/nINTSEL pin is latched on the rising edge of the nRST. The default setting is to float the
pin high for nINT mode.
nINTSEL Strapping and LED Polarity Selection
Figure 4.7 Direct Cable Connection vs. Cross-over Cable Connection
REF_CLK Out Mode
REF_CLK In Mode
Table 4.3 LED2/nINTSEL Configuration
MODE
DATASHEET
Figure
32
nINT/REFCLK0 is an active low interrupt output.
nINT/REFCLK0 is the source of REF_CLK.
4.8.
Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support
REF_CLK DESCRIPTION
SMSC LAN8720/LAN8720i
Datasheet

Related parts for lan8720