lan8710 Standard Microsystems Corp., lan8710 Datasheet - Page 9

no-image

lan8710

Manufacturer Part Number
lan8710
Description
Mii/rmii 10/100 Ethernet Transceiver With Hp Auto-mdix And Flexpwr Technology In A Small Footprint
Manufacturer
Standard Microsystems Corp.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lan8710A
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan8710A-EZC
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan8710A-EZC
0
Part Number:
lan8710A-EZC-TR
Manufacturer:
SMSC
Quantity:
15 000
Part Number:
lan8710A-EZC-TR
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan8710A-EZC-TR
0
Company:
Part Number:
lan8710A-EZC-TR
Quantity:
15 000
Part Number:
lan8710A-EZC-TR-ABC
0
Part Number:
lan8710A-EZK
Manufacturer:
Standard
Quantity:
1 920
Part Number:
lan8710A-EZK
Manufacturer:
SMSC
Quantity:
1 000
Part Number:
lan8710A-EZK
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan8710A-EZK-TR
Manufacturer:
SMSC
Quantity:
10 000
Part Number:
lan8710A-EZK-TR
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan8710A-EZK-TR
0
Company:
Part Number:
lan8710A-EZK-TR
Quantity:
2 000
Part Number:
lan8710AI-EZK
Manufacturer:
Standard
Quantity:
4 529
Part Number:
lan8710AI-EZK
Manufacturer:
GASIN
Quantity:
6 271
Part Number:
lan8710AI-EZK
Quantity:
50
Part Number:
lan8710AI-EZK
0
MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and flexPWR
Datasheet
Chapter 1 Introduction
SMSC LAN8710/LAN8710i
1.1
1.2
BYTE
FIFO
MAC
MII
RMII
N/A
X
RESERVED
SMI
TM
General Description
The following is list of the general terms used in this document:
The LAN8710/LAN8710i is a low-power 10BASE-T/100BASE-TX physical layer (PHY) transceiver that
transmits and receives on unshielded twisted-pair cable. A typical system application is shown in
Figure
The LAN8710/LAN8710i interfaces to the MAC layer using a variable voltage digital interface via the
standard MII (IEEE 802.3u). Support for RMII makes a reduced pin-count interface available. The
digital interface pins are tolerant to 3.6V.
The LAN8710/LAN8710i implements Auto-Negotiation to automatically determine the best possible
speed and duplex mode of operation. HP Auto-MDIX support allows using a direct connect LAN cable,
or a cross-over path cable.
The LAN8710 referenced throughout this document applies to both the extended commercial
temperature and industrial temperature components. The LAN8710i refers to only the industrial
temperature component.
General Terms and Conventions
1.2. It is available in both extended commercial and industrial temperature operating versions.
8-bits
First In First Out buffer; often used for elasticity buffer
Media Access Controller
Media Independent Interface
Reduced Media Independent Interface
Not Applicable
Indicates that a logic state is “don’t care” or undefined.
Refers to a reserved bit field or address. Unless otherwise noted, reserved
bits must always be zero for write operations. Unless otherwise noted, values
are not guaranteed when reading reserved bits. Unless otherwise noted, do
not read or write to reserved addresses.
Serial Management Interface
®
Technology in a Small Footprint
DATASHEET
9
TM
Revision 1.0 (04-15-09)

Related parts for lan8710