hsdl3208 Avago Technologies, hsdl3208 Datasheet
hsdl3208
Available stocks
Related parts for hsdl3208
hsdl3208 Summary of contents
Page 1
Description The HSDL-3208 is an ultra-small low cost infrared transceiver module that provides the interface between logic and infrared (IR) signals for through air, serial, half- duplex IR data link. The module is compliant to IrDA Physical Layer Specifications version ...
Page 2
Application Support Information The Application Engineering group in Agilent Technologies is available to assist you with the technical understanding Order Information Part Number Packaging Type HSDL-3208-021 Tape and Reel I/O Pins Configuration Table Pin Symbol 1 LED A 2 LED ...
Page 3
CAUTIONS: The BiCMOS inherent to the design of this component increases the component’s susceptibility to damage from the electrostatic discharge (ESD advised that normal static precautions be taken in handling and assembly of this component to prevent damage ...
Page 4
Electrical & Optical Specifications Specifications (Min. & Max. values) hold over the recommended operating conditions unless otherwise noted. Unspecified test conditions may be anywhere in their operating range. All typical values (Typ.) are with V to 3.0 ...
Page 5
V OH 90% 50% 10 Figure 3. RXD output waveform. TXD LED t pw (MAX.) Figure 5. TXD "stuck on" protection waveform. SD TXD TX LIGHT t TW Figure 7. TXD wakeup time waveform. ...
Page 6
Package Dimensions 7.00 ± 0.10 0.80 0.95 5.10 R 1.10 2.80 LED A LED C TXD RXD 0.95 (6X) 0.34 (5X) Figure 10. Package outline dimensions. 6 1.60 ± 0.10 0. GND CC 0.60 (7X) 0.40 ...
Page 7
Tape and Reel Dimensions UNIT: mm POLARITY PIN 7: GND PIN 1: LED A 0.3 ± 0.05 1.78 ± 0.1 EMPTY (40 mm MIN.) LABEL Figure 11. Tape and reel dimensions. 7 4.0 ± 0.1 1.75 ± 0.1 + 0.1 ...
Page 8
Moisture Proof Packaging All HSDL-3208 options are shipped in moisture proof package. Once opened, moisture absorption begins. This part is compliant to JEDEC Level 4. UNITS IN A SEALED MOISTURE-PROOF OPENED (UNSEALED) LESS THAN 30°C, AND LESS THAN NO BAKING ...
Page 9
Reflow Profile 230 200 183 170 R2 150 125 R1 100 HEAT SOLDER PASTE DRY UP Figure 13. Reflow graph. Process Zone Symbol Heat Up P1, R1 Solder Paste Dry P2, R2 Solder Reflow P3, ...
Page 10
Appendix A : SMT Assembly Application Note 1.0 Solder Pad, Mask and Metal Stencil Aperture STENCIL APERTURE SOLDER MASK Figure 14. Stencil and PCBA. 1.1 Recommended Land Pattern MOUNTING CENTER 0.10 1.75 0.60 UNIT: mm Figure 15. Stencil and PCBA. ...
Page 11
Recommended Metal Solder Stencil Aperture It is recommended that only a 0.152 mm (0.006 inches 0.127 mm (0.005 inches) thick stencil be used for solder paste printing. This is to ensure adequate printed solder paste volume and ...
Page 12
Appendix B: PCB Layout Suggestion The HSDL-3208 is a shieldless part and hence does not contain a shield trace, unlike the other transceivers. The following PCB layout guide- lines should be followed to obtain a good PSRR and EM immunity, ...
Page 13
Appendix C : General Application Guide for the HSDL-3208 Infrared ® IrDA Compliant 115.2 kb/s Transceiver Description The HSDL-3208 is an ultra-small low-cost infrared transceiver module that provides the interface between logic and infrared (IR) signals for through air, serial, ...
Page 14
RAM ROM PCMCIA CONTROLLER Figure 20: IR layout in PDA platform. The link distance testing is done using typical HSDL-3208 units with National Semiconductor’s PC87109 3V Super I/O Controller and SMC’s FDC37C669 and FDC37N769 Super I/O controllers. An 115.2 kb/s ...
Page 15
Appendix D: Window Designs for HSDL-3208 Optical port dimensions for HSDL-3208: To ensure IrDA compliance, some constraints on the height and width of the window exist. The minimum dimensions ensure that the IrDA cone angles are met without vignetting. The ...
Page 16
Module Depth Aperture Width (x, mm) (z) mm Max. Min. 0 8.76 6.80 1 9.92 7.33 2 11.07 7.87 3 12.22 8.41 4 13.38 8.94 5 14.53 9.48 6 15.69 10.01 7 16.84 10.55 8 18.00 11.09 9 19.15 11.62 ...
Page 17
Window Material Almost any plastic material will work as a window material. Polycarbonate is recommended. The surface finish of the plastic should be smooth, without any texture filter dye may be used in the window to make it ...
Page 18
For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6271 ...