hsdl3602 Avago Technologies, hsdl3602 Datasheet
hsdl3602
Available stocks
Related parts for hsdl3602
hsdl3602 Summary of contents
Page 1
Description The HSDL-3602 is a low-height infrared transceiver module that provides interface between logic and IR signals for through-air, serial, half-duplex IR data link. The module is compliant to IrDA Data Physical Layer Specifica- tions 1.1 and IEC825-Class 1 Eye ...
Page 2
The HSDL-3602 contains a high- speed and high-efficiency 870 nm LED, a silicon PIN diode, and an integrated circuit. The IC contains an LED driver and a receiver providing a single output (RXD) for all data rates supported. The HSDL-3602 ...
Page 3
Transceiver Control Truth Table Mode 0 Mode 1 FIR_SEL Don't Care Transceiver I/O Truth Table Transceiver Mode ...
Page 4
ILED vs LEDA 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 1.3 1.5 1.7 1.9 2.1 2.3 LEDA VOLTAGE (V) Marking Information The HSDL-3602-007/-037 is marked '3602YYWW' on the shield where 'YY' indicates the unit's manufactur- ing year, and 'WW' ...
Page 5
Recommended Operating Conditions Parameter Symbol Operating Temperature T A Supply Voltage V CC Logic High Input Voltage V IH for TXD, MD0, MD1, and FIR_SEL Logic Low Transmitter V IL Input Voltage LED (Logic High) Current I LEDA Pulse Amplitude ...
Page 6
Electrical & Optical Specifications Specifications hold over the Recommended Operating Conditions unless otherwise noted. Unspecified test conditions can be anywhere in their operating range. All typical values are at 25˚C and 3.3 V unless otherwise noted. Parameter Receiver Receiver Data ...
Page 7
TXD "Stuck ON" Protection TXD LED t pw (MAX.) LED Optical Waveform t pw LED ON 90% 50% 10% LED OFF RXD Output Waveform V OH 90% 50% 10 Receiver Wake Up Time Definition (when ...
Page 8
HSDL-3602-007 and HSDL-3602-037 Package Outline with Dimension and Recommended PC Board Pad Layout 2.45 0.80 1.20 4.05 SIDE VIEW ALL DIMENSIONS IN MILLIMETERS (mm). DIMENSION TOLERANCE IS 0.20 mm UNLESS OTHERWISE SPECIFIED. PIN 10 0.70 4.95 10 CASTELLATION: PITCH 1.1 ...
Page 9
Tape and Reel Dimensions (HSDL-3602-007, -037) ALL DIMENSIONS IN MILLIMETERS (mm) 13.00 ± 0.50 R 1.00 21.00 ± 0.80 LABEL SHAPE AND DIMENSIONS OF REELS A 10° 4 1.55 ± 0.05 3 5° (MAX.) 4.4 A 5.20 ...
Page 10
Moisture Proof Packaging All HSDL-3602 options are shipped in moisture proof package. Once opened, moisture absorption begins. UNITS IN A SEALED MOISTURE-PROOF OPENED (UNSEALED) LESS THAN 30°C, AND LESS THAN NO BAKING YES IS NECESSARY THAN 72 HOURS PERFORM RECOMMENDED ...
Page 11
Reflow Profile The reflow profile is a straight- line representation of a nominal temperature profile for a convec- tive reflow solder process. The temperature profile is divided into four process zones, each with different T/ time tempera- ture change rates. ...
Page 12
Appendix A: HSDL-3602-007/-037 SMT Assembly Application Note 1.0. Solder Pad, Mask, and Metal Solder Stencil Aperture STENCIL APERTURE SOLDER MASK Figure 1. Stencil and PCBA. 1.1. Recommended Land Pattern for HSDL-3602-007/-037 Dim. mm inches a 2.40 0.095 b 0.70 0.028 ...
Page 13
Adjacent Land Keep-out and Solder Mask Areas Dim. mm inches h min. 0.2 min. 0.008 j 13.4 0.528 k 4.7 0.185 l 3.2 0.126 Note : Wet/Liquid Photo-Imagineable solder resist/mask is recommended. Tx LENS LAND h Figure 3. HSDL-3602-007/-037 ...
Page 14
Recommended solder paste/ cream volume for castellation joints Based on calculation and experi- ment, the printed solder paste volume required per castellation pad is 0.30 cubic mm (based on either no-clean or aqueous solder cream types with typically 60 ...
Page 15
Tolerance for X-axis Alignment of Castellation Misalignment of castellation to the land pad should not exceed 0 approximately half the width of the castellation during placement of the unit. The castellations will completely self-align to the pads ...
Page 16
Y-axis Misalignment of Castellation In the Y-direction, the unit does not self-align after solder reflow recommended that the unit be placed in line with the fiducial mark (mid-length of land pad). This will enable sufficient land length ...
Page 17
Appendix B: General Application Guide for the HSDL-3602 Infrared ® IrDA Compliant 4 Mb/s Transceiver Description The HSDL-3602 wide voltage operating range infrared trans- ceiver is a low-cost and small form factor that is designed to address the mobile computing ...
Page 18
National Semiconductor Super I/O and Infrared Controller For National Semiconductor Super I/O and Infrared Controller chips, IR link can be realized with the following connections: IRTX PC97/87338VJG 63 PC87308VUL 81 PC87108AVHG 39 PC87109VBE 15 Please refer to the National ...
Page 19
HSDL-3602 Interoperability with National Semiconductor PC97338VJG SIO Evaluation Report Introduction The objective of this report is to demonstrate the interoperability of the HSDL-3602 IR transceiver IR module as wireless communi- cation ports at the speed of 2.4 kb/s - ...
Page 20
Standard Micro System Corporation (SMC) Super and Ultra I/O Controllers For SMC Super and Ultra I/O Controller chips, IR link can be realized with the following con- nections: • Connect IRTX of the SMC Super or Ultra I/O Controller ...
Page 21
Appendix C: Optical Port Dimensions for HSDL-3602: To ensure IrDA compliance, some constraints on the height and width of the window exist. The minimum dimensions ensure that the IrDA cone angles are met without vignetting. The maximum dimensions minimize the ...
Page 22
Aperture Width (x, mm) Module Depth, (z) mm max. 0 16.318 1 17.472 2 18.627 3 19.782 4 20.936 5 22.091 6 23.246 7 24.401 8 25.555 9 26.710 APERTURE WIDTH (X) vs MODULE DEPTH ...
Page 23
Window Material Almost any plastic material will work as a window material. Polycarbonate is recommended. The surface finish of the plastic should be smooth, without any texture filter dye may be used in the window to make it ...
Page 24
For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6271 ...