x96010 Intersil Corporation, x96010 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
x96010
Manufacturer Part Number
x96010
Description
Sensor Conditioner With Dual Look Up Table Memory And Dacs
Manufacturer
Intersil Corporation
Datasheet
1.X96010.pdf
(26 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
x96010V14IZ
Manufacturer:
IDT
Quantity:
989
BLOCK DIAGRAM
PIN ASSIGNMENTS
TSSOP
Pin
10
11
12
13
14
1
2
3
4
5
6
7
8
9
VSense
Name
VRef
SDA
VSense
SCL
Pin
Vcc
WP
Vss
A0
A1
A2
R1
R2
I1
I2
VRef
Device Address Select Pin 0. This pin determines the LSB of the device address required to com-
municate using the 2-wire interface. The A0 pin has an on-chip pull-down resistor.
Device Address Select Pin 1. This pin determines the intermediate bit of the device address re-
quired to communicate using the 2-wire interface. The A1 pin has an on-chip pull-down resistor.
Device Address Select Pin 2. This pin determines the MSB of the device address required to com-
municate using the 2-wire interface. The A2 pin has an on-chip pull-down resistor.
Supply Voltage.
Write Protect Control Pin. This pin is a CMOS compatible input. When LOW, Write Protection is
enabled preventing any “Write” operation. When HIGH, various areas of the memory can be protect-
ed using the Block Lock bits BL1 and BL0. The WP pin has an on-chip pull-down resistor, which en-
ables the Write Protection when this pin is left floating.
Serial Clock. This is a TTL compatible input pin. This input is the 2-wire interface clock controlling data
input and output at the SDA pin.
Serial Data. This pin is the 2-wire interface data into or out of the device. It is TTL compatible when
used as an input, and it is Open Drain when used as an output. This pin requires an external pull up
resistor.
Current Generator 1 Output. This pin sinks or sources current. The magnitude and direction of the
current is fully programmable and adaptive. The resolution is 8 bits.
Current Programming Resistor 1. A resistor between this pin and Vss can set the maximum output
current available at pin I1. If no resistor is used, the maximum current must be selected using control
register bits.
Current Programming Resistor 2. A resistor between this pin and Vss can set the maximum output
current available at pin I2. If no resistor is used, the maximum current must be selected using control
register bits.
Ground.
Sensor Voltage Input. This voltage input may be used to drive the input of the on-chip A/D converter.
Reference Voltage Input or Output. This pin can be configured as either an Input or an Output. As
an Input, the voltage at this pin is provided by an external source. As an Output, the voltage at this
pin is a buffered output voltage of the on-chip bandgap reference circuit. In both cases, the voltage
at this pin is the reference for the A/D converter and the two D/A converters.
Current Generator 2 Output. This pin sinks or sources current. The magnitude and direction of the
current is fully programmable and adaptive. The resolution is 8 bits.
A2, A1, A0
2
SDA
SCL
WP
Reference
Voltage
Interface
ADC
2-Wire
Mux
Mux
X96010
Pin Description
& Status
Look-up
Look-up
Control
Table 2
Table 1
Mux
Mux
DAC 2
DAC 1
R2
I2
R1
I1
October 25, 2005
FN8214.1