hc9p5502b1-5 Intersil Corporation, hc9p5502b1-5 Datasheet - Page 5

• Manufacturer Part Number: hc9p5502b1-5
• Description: Slic Subscriber Line Interface Circuit
• Manufacturer: Intersil Corporation

Pin Descriptions
28 PIN
PLCC
10
11
12
13
14
16
17
18
19
20
21
23
24
25
2
3
4
5
6
7
9
DIP/SOIC
24 PIN
10
11
12
13
14
15
16
17
18
19
20
21
1
2
3
4
5
6
7
8
9
SYMBOL
RING
GKD
SHD
OUT
4-5
V
V
+IN
TIP
DG
RD
BG
RC
RS
RF
PD
-IN
RX
C
C
TF
C
B
B
1
3
2
+
-
An analog input connected to the TIP (more positive) side of the subscriber loop through a 150
resistor and a ring relay contact. Functions with the Ring terminal to receive voice signals from the tele-
phone and for loop monitoring process.
An analog input connected to the RING (more negative) side of the subscriber loop through a 150 feed
resistor and a ring relay contact. Functions with the Tip terminal to receive voice signals from the tele-
phone and for loop monitoring purposes.
Positive Voltage Source - Most positive supply. V
Capacitor #1 - Optional Capacitor used to improve power supply rejection. This pin should be left open if un-
used.
Capacitor #3 - An external capacitor to be connected between this terminal and analog ground. Required
for proper operation of the loop current limiting function, and for filtering V
30V.
Digital Ground - To be connected to zero potential and serves as a reference for all digital inputs and out-
puts on the SLIC.
Ring Synchronization Input - A TTL - Compatible Clock Input. The clock should be arranged such that a
positive transition occurs on the negative going zero crossing of the ring voltage source, ensuring that the
ring relay is activated and deactivated when the instantaneous ring voltage is near zero. If synchronization
is not required, tie to 5V.
Relay Driver - A low active open collector logic output. When enabled, the external ring relay is energized.
Tip Feed - A low impedance analog output connected to the TIP terminal through a 150
Functions with the RF terminal to provide loop current, feed voice signals to the telephone set, and sink
longitudinal current.
Ring Feed - A low impedance analog output connected to the RING terminal through a 150 feed resistor.
Functions with the TF terminal to provide loop current, feed voice signal to the telephone set, and sink
longitudinal current.
Negative Voltage Source - Most negative supply. V
to -58V. Frequently referred to as “battery”.
Battery Ground - To be connected to zero potential. All loop current and some quiescent current flows into
this ground terminal.
Switch Hook Detection - A Low Active LS TTL - Compatible Logic Output. This output is enabled for loop
currents exceeding 10mA and disabled for loop currents less than 5mA.
Ground Key Detection - A Low Active LS TTL - Compatible Logic Output. This output is enabled if the DC
current into the ring lead exceeds the DC current out of the tip lead by more than 20mA, and disabled if
this current difference is less than 10mA.
Power Denial - A Low Active TTL - Compatible Logic Input. When enabled the switch hook detect (SHD)
and ground key detect (GKD) are not necessarily valid, and the relay driver (RD) output is disabled.
Ring Command - A Low Active TTL - Compatible Logic Input. When enabled, the relay driver (RD) output
goes low on the next rising edge of the ring sync (RS) input, as long as the SLIC is not in the power denial
state (PD = 0) or the subscriber is not already off- hook (SHD = 0).
Capacitor #2 - An external capacitor to be connected between this terminal and digital ground. Prevents
false ground key indications from occurring during ring trip detection. Typical value is 0.15 F, 10V. This
capacitor is not used if ground key function is not required.
The analog output of the spare operational amplifier.
The inverting analog input of the spare operational amplifier.
The non-inverting analog input of the spare operational amplifier.
Receive Input, Four Wire Side - A high impedance analog input which is internally biased. Capacitive cou-
pling to this input is required. AC signals appearing at this input differentially drive the Tip feed and Ring
feed amplifiers, which in turn drive tip and ring through 300 of feed resistance on each side of the line.
HC-5502B1
DESCRIPTION
B
+ is typically 12V or 5V.
B
- is typically -48V with an operational range of -42V
B
- supply. Typical value is 0.3 F,
feed resistor.
feed