hip6016cb Intersil Corporation, hip6016cb Datasheet - Page 6

• Manufacturer Part Number: hip6016cb
• Description: Advanced Pwm And Dual Linear Power Control
• Manufacturer: Intersil Corporation

Functional Pin Descriptions
VSEN1 (Pin 19)
This pin is connected to the PWM converter’s output voltage.
The PGOOD and OVP comparator circuits use this signal to
report output voltage status and for over voltage protection.
OCSET (Pin 20)
Connect a resistor (R
upper MOSFET. R
(I
set the PWM converter over-current (OC) trip point
according to the following equation:
I PEAK
An over-current trip cycles the soft-start function. Sustaining
an over-current for 2 soft-start intervals shuts down the
controller.
SS (Pin 9)
Connect a capacitor from this pin to ground. This capacitor,
along with an internal 11 A (typically) current source, sets
the soft-start interval of the converter.
Pulling this pin low with an open drain signal will shut down
the IC.
VID0, VID1, VID2, VID3, VID4 (Pins 6, 5, 4, 3 and 2)
VID0-4 are the input pins to the 5-bit DAC. The states of
these five pins program the internal voltage reference
(DACOUT). The level of DACOUT sets the core converter
output voltage. It also sets the core PGOOD and OVP
thresholds.
COMP and FB (Pins 17 and 18)
COMP and FB are the available external pins of the PWM
error amplifier. The FB pin is the inverting input of the error
amplifier. Similarly, the COMP pin is the error amplifier
output. These pins are used to compensate the voltage-
control feedback loop of the PWM converter.
GND (Pin 14)
Signal ground for the IC. All voltage levels are measured with
respect to this pin.
PGOOD (Pin 7)
PGOOD is an open collector output used to indicate the
status of the output voltages. This pin is pulled low when the
core output is not within 10% of the DACOUT reference
voltage and the other outputs are below their under-voltage
thresholds.
The PGOOD output is open for VID codes that inhibit
operation. See Table 1.
OCSET
=
), and the upper MOSFET on-resistance (r
I OCSET R OCSET
---------------------------------------------------------
r DS ON
OCSET
OCSET
, an internal 200 A current source
2-201
) from this pin to the drain of the
DS(ON)
)
HIP6016
PHASE (Pin 23)
Connect the PHASE pin to the PWM converter’s upper
MOSFET source. This pin is used to monitor the voltage
drop across the upper MOSFET for over-current protection.
UGATE (Pin 24)
Connect UGATE pin to the PWM converter’s upper MOSFET
gate. This pin provides the gate drive for the upper MOSFET.
PGND (Pin 21)
This is the power ground connection. Tie the PWM
converter’s lower MOSFET source to this pin.
LGATE (Pin 22)
Connect LGATE to the PWM converter’s lower MOSFET
gate. This pin provides the gate drive for the lower MOSFET.
VCC (Pin 1)
Provide a 12V bias supply for the IC to this pin. This pin also
provides the gate bias charge for all the MOSFETs
controlled by the IC.
RT (Pin 10)
This pin provides oscillator switching frequency adjustment.
By placing a resistor (R
200kHz switching frequency is increased according to the
following equation:
Conversely, connecting a pull-up resistor (R
to VCC reduces the switching frequency according to the
following equation:
FAULT (Pin 8)
This pin is low during normal operation, but it is pulled to VCC
in the event of an over-voltage or over-current condition.
GATE3 (Pin 15)
Connect this pin to the gate of an external MOSFET. This pin
provides the drive for the linear controller’s pass transistor.
VSEN3 (Pin 16)
Connect this pin to V
regulated to 1.5V.
VOUT2 (Pin 13)
Output of the linear regulator. Supplies current up to 230mA
(typically).
VSEN2 (Pin 11)
Connect this pin to remote sense the V
voltage at this pin is regulated to 2.5V.
Fs 200kHz
Fs 200kHz
+
–
-------------------- -
R
-------------------- -
R
4 10
5 10
T
T
k
k
7
6
OUT3
T
) from this pin to GND, the nominal
(R
(R
. The voltage at this pin is
T
T
to 12V)
to GND)
OUT2
T
) from this pin
output. The