xr16v2550im Exar Corporation, xr16v2550im Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16v2550im
Manufacturer Part Number
xr16v2550im
Description
High Performance Duart With 16-byte Fifo
Manufacturer
Exar Corporation
Datasheet
1.XR16V2550IM.pdf
(48 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16v2550im-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
xr16v2550im-F
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
REV. 1.0.2
The V2550 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the V2550 to enter sleep mode:
The V2550 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The V2550 resumes normal operation by any of the following:
If the V2550 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the V2550 is awakened by the modem inputs, a
read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while
an interrupt is pending from channel A or B. The V2550 will stay in the sleep mode of operation until it is
disabled by setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, and modem input lines remain steady when the
V2550 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on
current can be up to 100 times more. If any of those signals are toggling or floating, then an external buffer
would be required to keep the address, data and control lines steady to achieve the low current. As an
alternative, please refer to the XR16V2551 which is pin-to-pin and software compatible with the V2550 but with
(some additional pins and) the PowerSave feature that eliminates any unnecessary external buffer.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX A/B inputs idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition
upon the restart. This may occur when the external interface transceivers (RS-232, RS-422 or another type)
are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a
47k-100k ohm pull-up resistor on the RXA and RXB pins.
2.19
■
■
■
■
■
■
■
no interrupts pending for both channels of the V2550 (ISR bit-0 = 1)
sleep mode of both channels are enabled (IER bit-4 = 1)
modem inputs are not toggling (MSR bits 0-3 = 0)
RX input pins are idling HIGH
a receive data start bit transition (HIGH to LOW)
a data byte is loaded to the transmitter, THR or FIFO
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
Sleep Mode with Auto Wake-Up
page
37. If the input lines are floating or are toggling while the V2550 is in sleep mode, the
19
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
XR16V2550