xr16v2550im Exar Corporation, xr16v2550im Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16v2550im
Manufacturer Part Number
xr16v2550im
Description
High Performance Duart With 16-byte Fifo
Manufacturer
Exar Corporation
Datasheet
1.XR16V2550IM.pdf
(48 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16v2550im-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
xr16v2550im-F
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
XR16V2550
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
MCR[2]: IrDA RX Inversion or OP1# (legacy term)
When Infrared mode is enabled (MCR[6]=1 and EFR[4]=1), this bit selects the idle state of the encoded IrDA
data. In internal loopback mode, this bit functions like the OP1# in the 16C550.
•
•
In the Internal Loopback Mode, this bit controls the state of the modem input RI# bit in the MSR register as
shown in
MCR[3]: OP2# Output / INT Output Enable
This bit enables or disables the operation of INT, interrupt output. If INT output is not used, OP2# can be used
as a general purpose output.
•
•
MCR[4]: Internal Loopback Enable
•
•
MCR[5]: Xon-Any Enable (requires EFR bit-4=1)
•
•
MCR[6]: Infrared Encoder/Decoder Enable (requires EFR bit-4=1)
•
•
MCR[7]: Clock Prescaler Select (requires EFR bit-4=1)
•
•
This register provides the status of data transfers between the UART and the host.
LSR[0]: Receive Data Ready Indicator
•
•
4.8
Logic 0 = Select RX input as active-low encoded IrDA data (Idle state will be low) (default).
Logic 1 = Select RX input as active-high encoded IrDA data (Idle state will be high).
Logic 0 = INT (A-B) outputs disabled (three state mode) and OP2# output set HIGH(default).
Logic 1 = INT (A-B) outputs enabled (active mode) and OP2# output set LOW.
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO, unless the RX character is an Xon or Xoff character and
the V2550 is programmed to use the Xon/Xoff flow control.
Logic 0 = Enable the standard modem receive and transmit input/output interface (default).
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. The TX/RX output/input are routed to the
infrared encoder/decoder. The data input and output levels conform to the IrDA infrared interface
requirement. While in this mode, the infrared TX output will be idling LOW.
PAGE 18.
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
Line Status Register (LSR) - Read Only
Figure
To change the polarity of the IrDA data at the Rx input, see MCR[2].
12.
30
Figure
12.
SEE”INFRARED MODE” ON
REV. 1.0.2