xr16v2651im Exar Corporation, xr16v2651im Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16v2651im
Manufacturer Part Number
xr16v2651im
Description
High Performance Duart With 32-byte Fifo And Powersave
Manufacturer
Exar Corporation
Datasheet
1.XR16V2651IM.pdf
(51 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16v2651im-F
Manufacturer:
Exar Corporation
Quantity:
10 000
XR16V2651
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO AND POWERSAVE FEATURE
]
ISR[0]: Interrupt Status
•
•
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source
Table
ISR[4]: Xoff/Xon or Special Character Interrupt Status
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-4 indicates that the receiver detected a data match
of the Xoff character(s). If this is an Xoff/Xon interrupt, it can be cleared by a read to the ISR. If it is a special
character interrupt, it can be cleared by reading ISR or it will automatically clear after the next character is
received.
ISR[5]: RTS#/CTS# Interrupt Status
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-5 indicates that the CTS# or RTS# has been de-
asserted.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
•
•
4.5
P
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition) or the device has come out of sleep mode.
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
RIORITY
L
EVEL
1
2
3
4
5
6
7
-
11).
FIFO Control Register (FCR) - Write-Only
B
IT
0
0
0
0
0
0
1
0
-5
B
IT
0
0
0
0
0
1
0
0
-4
ISR R
B
T
EGISTER
IT
0
1
0
0
0
0
0
0
ABLE
-3
11: I
B
S
IT
TATUS
1
1
1
0
0
0
0
0
-2
NTERRUPT
B
B
ITS
IT
1
0
0
1
0
0
0
0
-1
S
OURCE AND
28
B
IT
0
0
0
0
0
0
0
1
-0
LSR (Receiver Line Status Register)
RXRDY (Receive Data Time-out)
RXRDY (Received Data Ready)
TXRDY (Transmit Ready)
MSR (Modem Status Register)
RXRDY (Received Xoff or Special character)
CTS#, RTS# change of state
None (default) or Wake-up Indicator
P
RIORITY
L
EVEL
S
OURCE OF INTERRUPT
REV. 1.0.2