as7c33512ft32a Alliance Memory, Inc, as7c33512ft32a Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
as7c33512ft32a
Manufacturer Part Number
as7c33512ft32a
Description
3.3v 512k 32/36 Flow-through Synchronous Sram
Manufacturer
Alliance Memory, Inc
Datasheet
1.AS7C33512FT32A.pdf
(19 pages)
Functional description
The AS7C33512FT32A/36A is a high-performance CMOS 16-Mbit synchronous Static Random Access Memory (SRAM) device organized
Burst operation is initiated in one of two ways: the controller address strobe (ADSC), or the processor address strobe (ADSP). The burst
advance pin (ADV) allows subsequent internally generated burst addresses.
Read cycles are initiated with ADSP (regardless of WE and ADSC) using the new external address clocked into the on-chip address register
when ADSP is sampled low, the chip enables are sampled active, and the output buffer is enabled with OE. In a read operation, the data
accessed by the current address registered in the address registers by the positive edge of CLK are carried to the data-out buffer. ADV is
ignored on the clock edge that samples ADSP asserted, but is sampled on all subsequent clock edges. Address is incremented internally for
the next access of the burst when ADV is sampled low and both address strobes are high. Burst mode is selectable with the LBO input. With
LBO unconnected or driven high, burst operations use an interleaved count sequence. With LBO driven low, the device uses a linear count
sequence.
Write cycles are performed by disabling the output buffers with OE and asserting a write command. A global write enable GWE writes all 32/
36 regardless of the state of individual BW[a:d] inputs. Alternately, when GWE is high, one or more bytes may be written by asserting BWE
and the appropriate individual byte BWn signals.
BWn is ignored on the clock edge that samples ADSP low, but it is sampled on all subsequent clock edges. Output buffers are disabled when
BWn is sampled LOW regardless of OE. Data is clocked into the data input register when BWn is sampled low. Address is incremented
internally to the next burst address if BWn and ADV are sampled low.
Read or write cycles may also be initiated with ADSC instead of ADSP. The differences between cycles initiated with ADSC and ADSP are
as follows:
The AS7C33512FT32A and AS7C33512FT36A family operates from a core 3.3V power supply. I/Os use a separate power supply that can
operate at 2.5V or 3.3V. These devices are available in 100-pin TQFP package.
TQFP capacitance
*Guaranteed not tested
TQFP thermal resistance
1 This parameter is sampled
as 524,288 words x 32/36.
Fast cycle times of 8.5/10/12 ns with clock access times (t
Input capacitance
I/O capacitance
Thermal resistance
(junction to ambient)
Thermal resistance
(junction to top of case)
12/23/04, v 1.4
• ADSP must be sampled high when ADSC is sampled low to initiate a cycle with ADSC.
• WE signals are sampled on the clock edge that samples ADSC low (and ADSP high).
• Master chip enable CE0 blocks ADSP, but not ADSC.
Description
Parameter
1
1
Test conditions follow standard test methods and
procedures for measuring thermal impedance,
Symbol
C
C
I/O
IN
*
*
per EIA/JESD51
Alliance Semiconductor
Conditions
CD
) of 7.5/8.5/10 ns. Three chip enable (CE) inputs permit easy memory expansion.
Test conditions
V
V
OUT
IN
= 0V
= 0V
®
1–layer
4–layer
Min
Symbol
-
-
θ
θ
θ
JA
JA
JC
AS7C33512FT32A
AS7C33512FT36A
Typical
Max
40
22
7
8
5
4 of 19
Units
°C/W
°C/W
°C/W
Unit
pF
pF