92hd71b5x5prgxb3x8 Integrated Device Technology, 92hd71b5x5prgxb3x8 Datasheet - Page 29

• Manufacturer Part Number: 92hd71b5x5prgxb3x8
• Description: Four Channel Hd Audio Codec, Low Power Optimized, 4-ports, 95db Snr
• Manufacturer: Integrated Device Technology

4-CHANNEL HD AUDIO CODECS OPTIMIZED FOR LOW POWER
Voltage Reference Outputs
Phased Locked Loop
ESD / Latchup
92HD71B5
4-CHANNEL HD AUDIO CODECS OPTIMIZED FOR LOW POWER
VREFOut
VREFILT (VAG)
PLL lock time
PLL (or Azalia Bit CLK) 24MHz clock jitter
Latch-up
ESD - Human Body Model
Charged Device Model
1.Dynamic Range is the ratio of the full scale signal to the noise output with a -60dBFS signal as defined in AES17 as SNR in the
presence of signal and outlined in AES6id, measured “A weighted” over 20 Hz to 20 kHz bandwidth.
2.Ratio of Full Scale signal to idle channel noise output is measured “A weighted” over a 20 Hz to a 20 kHz bandwidth.
(AES17-1991 Idle Channel Noise or EIAJ CP-307 Signal-to-noise Ratio).
3.THD+N ratio as defined in AES17 and outlined in AES6id,non-weighted, over 20 Hz to 20 kHz bandwidth.Results at the jack
are dependent on external components and will likely be 1 - 2dB worse.
4.Peak-to-Peak Ripple over Passband meets ± 0.125dB limits, 48 kHz or 44.1 kHz Sample Frequency. 1dB limit.
5.Stop Band rejection determines filter requirements. Out-of-Band rejection determines audible noise.
6.The integrated Out-of-Band noise generated by the DAC process, during normal PCM audio playback, over a bandwidth 28.8
to 100 kHz, with respect to a 1 Vrms DAC output.
7.Gain drift is the change in analog volume control gain for each step across the supported 0
referenced to the 25
8.± 1dB limits for Line Output & 0 dB gain, at -20dBV
9.Spurious tone rejection is tested with ADC dither enabled and compared to ADC performance without dither.
10.Does not include 32
11.Can be set to 0.5 or 0.8 AVdd.
(All converters/ports enabled)
(All converters/ports enabled)
11
Parameter
D0 Didd
D0 Aidd
D1 Didd
D1 Aidd
D2 Didd
D2 Aidd
D3 Didd
D3 Aidd
o
C gain value and specified in ppm per
Table 13. 92HD71B7 5V, 4.75V, and 3.3V Analog Performance Characteristics
Ω
load headphone power.
As described in JESD78A Class II
As described in JESD22-A114-B
As described in JESD22-C101
5.0V, 4.75V, & 3.3V
5.0V, 4.75V, & 3.3V
5.0V, 4.75V, & 3.3V
5.0V, 4.75V, & 3.3V
Conditions
o
3.3V
3.3V
3.3V
3.3V
C
29
AVdd
All
All
All
All
All
All
All
92HD71B5
Min
500
o
2K
C TO 70
-
-
-
-
-
-
-
-
-
0.45 X
0.5 X
AVdd
AVdd
Typ
150
1K
39
53
13
25
13
18
10
96
70
3K
8
o
C temperature range
Max
200
500
-
-
-
-
-
-
-
-
-
PC AUDIO
V 1.0, 01/08
degC
usec
psec
Unit
mA
mA
mA
mA
mA
mA
mA
mA
V
V
V
V