mt90520 Zarlink Semiconductor, mt90520 Datasheet - Page 58
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
mt90520
Manufacturer Part Number
mt90520
Description
8-port Primary Rate Circuit Emulation Aal1 Sar
Manufacturer
Zarlink Semiconductor
Datasheet
1.MT90520.pdf
(180 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 58 of 180
- Download datasheet (2Mb)
4.5.2
In the UDT mode of operation, the TX_SAR is capable of generating and transmitting cells for 8 independent VCs,
representing each of the 8 TDM ports of the MT90520 device.
4.5.2.1
The first step in setting up the TX_SAR for UDT operation is the configuration of a UDT Segmentation Control
Structure, as shown in Figure 20.
There must be one control structure for each UDT VC that the TX_SAR is to transmit. A control structure may be
located at any address within the internal memory space which is reserved for Segmentation Control Structures
(starting at byte address 80000h). The TX_SAR hardware identifies the location of a particular control structure by
reading the TX_SAR Pointer Table Base Register for the corresponding TDM port. These registers are located at
byte addresses 1000h + p*2h, where p represents the particular port number. Within these registers, the user must
configure the least-significant 14 bits to point to the word address of the start of a UDT Segmentation Control
Structure in internal memory. As well, the TXCFG bits in the register must be set to “01” to indicate that the control
structure being pointed to is formatted for UDT transmission.
All of the fields within the control structure are explained in the text accompanying Figure 20. Upon initialization,
several of the fields within the UDT Segmentation Control Structure need to be explicitly configured by the user. The
GFC, VPI, and VCI fields must be programmed to configure the header of the outgoing cells to contain the correct
routing information. The user may also program the PTI and CLP fields to configure the networking properties for
the cells on the VC. Additionally, the user can configure the HEC and UDF2 fields of outgoing cells. The HEC field
is used primarily as a place-holder since PHY devices are usually responsible for the generation of header error
checking values. The value contained in the UDF2 field is only transmitted in outgoing cells if the MT90520 is using
a 16-bit UTOPIA interface. If the VC is going to be carrying RTS nibbles, the SE bit must be set, as detailed in the
figure above. The remaining fields in the control structure should be cleared upon initialization.
Once the control structure has been configured, the transmission of CBR cells can begin as soon as the TX_SAR is
enabled, by setting the TXENB bit in the TX_SAR Master Enable Register at byte address 1044h.
Byte
Add
+00
+02
+04
+06
+08
Note 1: Fields which appear in dark grey are reserved fields
which must be cleared by software upon initialization.
Note 2: Fields which appear in light grey are those which are
updated by hardware.
UDT Mode of Operation
Control Structure Configuration
15
14
GFC
13
Reserved
HEC
12
11
Cell Count Statistic
10
VCI
9
8
VPI
7
Figure 20 - Segmentation Control Structure - UDT Format
SRTS
6
5
UDF2
4
3
S
E
PTI
2
VCI
SN
1
C
0
Word
+00
+01
+02
+03
+04
Zarlink Semiconductor Inc.
Add
MT90520
SRTS: If SE is set, an RTS value is read from the Clock Management module at the
beginning of each cell sequence (i.e., sequence number = 0) and stored in this field.
In cells with odd sequence numbers, the MSB from this field is placed into the CSI bit
of the SAR-PDU header. The SRTS value is then shifted left. A complete RTS nibble
is sent in each 8-cell sequence.
SE (SRTS Enable): When set, indicates that the VC is transmitting SRTS data.
When cleared, the CSI bit of outgoing cells is cleared to ‘0’.
SN (Sequence Number): Sequence number of the next cell to be transmitted.
Should be initialized to “0” by software.
GFC: The Generic Flow Control value is placed in the GFC field of the cell header in
a UNI cell. If the cell is using NNI formatting, these bits hold the four MSB of the VPI.
VPI: This value is placed in the VPI field of outgoing cell headers.
VCI: This value is placed in the VCI field of outgoing cell headers.
PTI: This value is placed in the PTI field of the generated cell headers.
C (CLP): This value is placed in the CLP field of outgoing cell headers.
HEC: This value is placed in the HEC field of outgoing cell headers. The physical
layer is generally responsible for calculating HEC values; therefore, this field is used
as a place holder. If the physical layer does not calculate the HEC, the user may
generate the appropriate HEC value by performing a modulo-2 division of the first
four octets of the cell header using the generator polynomial G(x) = x
UDF2: This value is placed in the UDF2 field of the cell header when the UTOPIA
interface is operating in 16-bit mode.
Cell Count Statistic: Rollover counter which counts the number of cells transmitted
on this VC by the TX_SAR module. Should be initialized to “0” by software.
58
Data Sheet
8
+ x
2
+ x + 1.
Related parts for mt90520
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SL1430](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Zarlink Semiconductor Inc [TV IF PREAMPLIFIER]
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT8980DC](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
256 x 256 Channels (8 TDM Streams @ 2.048Mb/s) Non-blocking Digital Switch (DX)
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT8981DE](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MV3508](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MV1822DIG](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet:
![SP8853B](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MV1820FCG](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Video Programme Delivery Control Interface Circuit
Manufacturer:
Zarlink Semiconductor
Datasheet:
![SP8719](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
SP8719520MHz LOW CURRENT TWO-MODULUS DIVIDERS
Manufacturer:
Zarlink Semiconductor
Datasheet:
![ML922](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
REMOTE CONTROL RECEIVER
Manufacturer:
Zarlink Semiconductor
Datasheet:
![SP4982](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
2·5GHz ÷8192 PRESCALER
Manufacturer:
Zarlink Semiconductor
Datasheet:
![SP4740](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
1·3GHz 4256 PRESCALER WITH LOW CURRENT AND LOW RADIATION
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT8980DP](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT3171BE](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT88E45AS](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT8952BE](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Manufacturer:
Zarlink Semiconductor
Datasheet: