zl50060gag2 Zarlink Semiconductor, zl50060gag2 Datasheet - Page 46
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
zl50060gag2
Manufacturer Part Number
zl50060gag2
Description
16 K Channel Digital Switch With High Jitter Tolerance, Per Stream Rate Conversion 2, 4, 8, 16 Or 32 Mbps , 64 Input And 64 Output Streams Pin Compatible With Mt90869
Manufacturer
Zarlink Semiconductor
Datasheet
1.ZL50060GAG2.pdf
(99 pages)
and BE) of the respective connection memories should be set to HIGH to enable the outputs for the selected
channels.
The BER receive channel numbering is not affected by the input channel delay value. It means that the BER
receive circuitry always assume there is no input channel delay, regardless of the values of the BCDR and LCDR
registers. For example, if BER data is received on local input stream 0 channel 3, without input channel delay, the
LBSRR (Local BER Start Receive Register) should be programmed to 3. With input channel delay of 5, however,
the LBSRR should be programmed to 8 (3 + 5) instead.
Note that when BER transmission is enabled, the target channels will carry PRBS data, and the rest of the channels
on all streams of the same side (Local/Backplane) will carry unknown data, which renders that side of the switch
unable to switch traffic during BER test.
7.0
The 16 K switch family supports non-multiplexed Motorola type microprocessor buses. The microprocessor port
consists of a 16-bit parallel data bus (D0-15), a 15-bit address bus (A0-14) and four control signals (CS, DS, R/W
and DTA). The data bus provides access to the internal registers, the Backplane Connection and Data Memories,
and the Local Connection and Data Memories. Each memory has 8,192 locations. See Table 11, Address Map for
Data and Connection Memory Locations (A14 = 1), for the address mapping.
Each Connection Memory can be read or written via the 16-bit microprocessor port. The Data Memories can only
be read (but not written) from the microprocessor port.
To prevent the bus ’hanging’, in the event of the switch not receiving a master clock, the microprocessor port shall
complete the DTA handshake when accessed, but any data read from the bus will be invalid.
8.0
8.1
The recommended power-up sequence is for the V
power-up of the V
powered up simultaneously, but neither should 'lead' the V
All supplies may be powered-down simultaneously.
8.2
Upon power up, the device should be initialized by applying the following sequence:
1
2
3
Power-Up Sequence
Initialization
Microprocessor Port
Device Power-up, Initialization and Reset
Ensure the TRST pin is permanently LOW to disable the JTAG TAP controller.
Set ODE pin to LOW. This configures the LCSTo0-3 output signals to LOW (i.e., setting optional external
output buffers to high impedance), and sets the LSTo0-31 outputs to HIGH or high impedance,
dependent on the LORS input value, and sets the BCSTo0-3 output signals to LOW (i.e., setting optional
external output buffers to high impedance), and sets the BSTo0-31 outputs to HIGH or high impedance,
dependent on BORS input value. Refer to Pin Description for details of the LORS and BORS pins.
Reset the device by asserting the RESET pin to zero for at least two cycles of the input clock, C8i. A
delay of an additional 250 s must also be applied before the first microprocessor access is
performed following the de-assertion of the RESET pin; this delay is required for determination of the
input frame pulse format.
DD_PLL
and V
DD_CORE
supplies (nominally +1.8 V). The V
Zarlink Semiconductor Inc.
ZL50060/1
DD_IO
46
DD_IO
supply (nominally +3.3 V) to be established before the
supply by more than 0.3 V.
DD_PLL
and V
DD_CORE
supplies may be
Data Sheet