am79q02 ETC-unknow, am79q02 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
am79q02
Manufacturer Part Number
am79q02
Description
Quad Subscriber Line Audio-processing Circuit Qslac Devices
Manufacturer
ETC-unknow
Datasheet
1.AM79Q02.pdf
(68 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
am79q021JC
Manufacturer:
AMD
Quantity:
12
Company:
Part Number:
am79q021JC
Manufacturer:
AMD
Quantity:
5 510
Part Number:
am79q021JC
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
am79q021VC
Manufacturer:
AMD
Quantity:
13 888
Company:
Part Number:
am79q02JC
Manufacturer:
ST
Quantity:
5 510
Power Supply
Two separate power supply inputs are provided to
allow for noise isolation and proper power supply
decoupling techniques; however, the two pins have a
low impedance connection inside the part. For best
performance, all of the +5.0 power supply pins should
be connected together at the connector of the printed
circuit board, and all of the grounds should be
connected together at the connector of the printed
circuit board.
FUNCTIONAL DESCRIPTION
The QSLAC device performs the codec/filter and two-
to four-wire conversion functions required of the
s u b s c r i b e r
telecommunications equipment. These functions
involve converting audio signals into digital PCM
samples and converting digital PCM samples back into
audio signals. During conversion, digital filters are
used to band limit the voice signals. All of the digital
filtering is performed in digital signal processors
operating from a master clock, which can be derived
either from PCLK or MCLK.
Four independent channels allow the QSLAC device to
function as four SLAC devices or two DSLAC ä
devices. For programming information, each channel
has its own enable bit (EC1, EC2, EC3, and EC4) to
allow individual channel programming. If more than
one Channel Enable bit is High or if all Channel Enable
10
Pin Names
VOUT
VOUT
VREF
AGND
DGND
VCCA
VCCD
PCM Highway
1
4
–
Single
Single
Dual
Outputs
Output
l i n e
Type
Analog ground
Digital ground
+5.0 V analog power supply
+5.0 V digital power supply
i n t e r fa c e
Programmable I/O
Analog. The received digital data at DRA or DRB is processed and converted to an analog
signal at the VOUT pin. VOUT
2, VOUT
voltages are referenced to VREF.
Analog Voltage Reference. The VREF output is provided in order for an external 0.1 µF ca-
pacitor to be connected from VREF to ground, filtering noise present on the internal voltage
reference. VREF is buffered before it is used by internal circuitry. The voltage on VREF is
nominally 2.1 V, and the output resistance is 100 kΩ ±30%. The leakage current in the ca-
pacitor must be less than 20 nA.
Four
Five
Two
c i r c u i t r y
3
Am79Q02/021/031 Data Sheet
is the output from channel 3, and VOUT
Chopper Clock
i n
Yes
No
No
1
is the output from channel 1, VOUT
bits are High, all channels enabled will receive the
programming infor mation wr itten; therefore, a
Broadcast state can be implemented by simply
enabling all channels in the device to receive the
information. The Channel Enable bits are contained in
the Channel Enable register, which is written and read
using Commands 14 and 15. The Broadcast state is
useful in initializing QSLAC devices in a large system.
The user-programmable filters set the receive and
transmit gain, perform the transhybrid balancing
function, permit adjustment of the two-wire termination
impedance, and provide equalization of the receive and
transmit paths. All programmable digital filter
coefficients can be calculated using the AmSLAC4 or
WinSLAC™ software.
Data transmitted or received on the PCM highway can
be 8-bit companded code (with an optional 8-bit
signaling byte in the transmit direction) or 16-bit linear
code. The 8-bit codes appear 1 byte per time slot,
while the 16-bit code appears in two consecutive time
slots. The compressed PCM codes can be either 8-bit
companded A-law or µ-law. The PCM data is read from
and written to the PCM highway in user-programmable
time slots at rates of 128 kHz to 8.192 MHz. The
transmit clock edge and clock slot can be selected for
compatibility with other devices that can be connected
to the PCM highway.
Three configurations of the QSLAC device are
offered with single or dual PCM highways. The
Am79Q02 and Am79Q021 QSLAC devices with dual
and single PCM highways respectively are available
in the 44-pin packages. The Am79Q031JC QSLAC
device is a single PCM highway version in a 32-pin
PLCC package.
Description
44 PLCC/TQFP
44 PLCC/TQFP
32 PLCC
Package
4
is the output for channel 4. The VOUT
Am79Q02 JC
Am79Q021 JC (or VC)
Am79Q031 JC
2
is the output for channel
Part Number