lv4993m Sanyo Semiconductor Corporation, lv4993m Datasheet
lv4993m
Related parts for lv4993m
lv4993m Summary of contents
Page 1
... Ordering number : ENA1962 LV4993M Overview LV4993M built-in the power amplifier circuit operable at low voltage (1.8V or more) and has additionally the standby function to reduce the current drain power amplifier IC optimal for speaker drive used in battery-driven portable equipment and the low output power system equipment. ...
Page 2
... Reference (pin 1) voltage VREF Pin 2 control HIGH voltage VSTBH Pin 2 control LOW voltage VSTBL Pin 4 control HIGH voltage VCNTH Pin 4 control LOW voltage VCNTL LV4993M Conditions PCB mounted* Symbol Conditions op1 RL=8 to 32Ω, Ta=-10 to 85° op2 RL=8 to 32Ω, Ta=-40 to 85° op3 RL=4 to 7Ω ...
Page 3
... Package Dimensions unit : mm (typ) 3032E 5 (0.6) 1.27 0.15 0.35 SANYO : MFP8(225mil) Evaluation board Size : 50mm×40mm×1.6mm Top Layer(Top view) LV4993M Pd max -- Ta 1200 Specified board: 50×40×1.6mm Specified board 1000 (Both side) 900 800 600 400 Independent IC 300 0 -40 - Ambient temperature ...
Page 4
... Block Diagram and Sample Application Circuit IN 1 STBY from CPU 2 VREF 3 CNT from CPU 4 Test Circuit STBY LV4993M AMP1 - + V CC BIAS TSD - CONTROL + AMP2 1 2 LV4993M OUT1 GND GND 6 OUT2 No.A1962-4/13 ...
Page 5
... OUT2 2.5 6 GND External impression 8 OUT1 2.5 LV4993M Description Input pin Standby control pin •Standby mode 0.3V •Operation mode at 1 Standard voltage pin Second amplifier stop control pin •When OPEN : BTL mode •When external is impressed BTL mode at 1. mode o.3V ...
Page 6
... Figure 1 when the standby function is not used. Please set the value of series resistance (R3) so that 2nd pin voltage may become 3V or less. Current ( that flows in 2nd pin can be calculated by the next formula. -6 +(V CC −0.7) 7* R3+30000 LV4993M STBY 2 Fig. 1 ...
Page 7
... When IC is used near the maximum rating, there is a possibility that the maximum rating may be exceeded even under the smallest change of conditions, resulting in failure. Take the sufficient margin for variation of supply voltage and use IC within a range where the maximum rating will never be exceeded. LV4993M No.A1962-7/13 ...
Page 8
... Supply voltage 0.7 0.6 0.5 0.4 0.3 0.2 0 0.01 0.1 Output power LV4993M 100 fin =1kHz 6dB 0 0. 200mW VG = 6dB ...
Page 9
... V4 =0.3V --120 --125 --40 --35 --30 --25 --20 --15 Input voltage, Vin -- dBV SVRR -- 0.01 0.1 Frequency LV4993M 1000 100 0.01 1000 100 ...
Page 10
... Supply voltage Istby -- Ta 10000 no signal 7 no load 0. 1000 100 --40 -- Ambient temperature LV4993M load no signal 3.5 3 2 0.5 V 100 no signal no load signal no load 3 ...
Page 11
... Output power 1.8 1.6 1.4 1.2 1 0.8 --40 -- Ambient temperature 6.5 6 5.5 5 --40 -- Ambient temperature LV4993M 100 0 0.01 0.2 0.18 0.16 0.14 0.12 0.1 0.08 80 100 --40 --20 --90 --100 --110 --120 80 100 ...
Page 12
... Time axis:50msec/div Mute release Transient response characteristics (ON→OFF) CH1:Load end [100mV/div] CH2:8pin (OUT1) [1V/div] CH3:4pin (CNT) [2V/div] Time axis:2msec/div LV4993M Falling Transient response characteristics CH1:Load end [100mV/div] CH2:8pin (OUT1) [1V/div] CH3:2pin (STBY) [2V/div] Time axis:50msec/div Mute Transient response characteristics (OFF→ON) ...
Page 13
... SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of June, 2011. Specifications and information herein are subject to change without notice. LV4993M PS No.A1962-13/13 ...