lc75374e Sanyo Semiconductor Corporation, lc75374e Datasheet

no-image

lc75374e

Manufacturer Part Number
lc75374e
Description
Electronic Volume And Tone Control For Car Stereos
Manufacturer
Sanyo Semiconductor Corporation
Datasheet
Ordering number : EN5835
Overview
The LC75374E is an electronic volume and tone control
circuit that provides volume, balance, fader, bass and
treble, super bass, input switching, and input and output
level controls and requires a minimal number of external
components to implement these functions.
Functions
• Volume: 0dB to –79dB (in 1-dB steps) and –∞dB for a
• Fader: Allows either the rear or the front channel outputs
• Bass and treble: NF-type tone control circuits are form–
• Input gain: The input signal can be amplified by 0dB to
• Output gain: The fader output can be set to one of three
• Input switching: Both the left and right channels can be
• Super bass: This circuit provides peaking characteristics
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
to be attenuated over 16 positions.
(0 to –20dB in 2dB steps, –20 to –25dB in a 5dB
step, –25 to –45dB in 10dB steps, –60dB, and
–∞dB for a total of 16 positions.)
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
• CCB is a trademark of SANYO ELECTRIC CO., LTD.
• CCB is SANYO’s original bus format and all the bus
total of 81 positions.
A balance function can be implemented by
controlling the left and right channels
independently.
+18.75dB (in 1.25dB steps).
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
addresses are controlled by SANYO.
(T type characteristics) and 11 position sett–
ings.
settings: 0dB, +6.5dB, or +8.5dB.
ed using external CR circuits. The bass
and treble can be controlled from 0dB
to +11.9dB (in 1.7dB steps) for a total
of 15 positions.
selected from one of four inputs.
Electronic Volume and Tone Control for Car Stereos
Features
• On-chip buffer amplifiers minimizes the number of
• Built-in reference voltage generator for the analog
• All controls can be set using the serial data input circuit
Package Dimensions
unit: mm
3148-QIP44MA
external components.
ground.
(CCB).
[LC75374E]
N3098RM (OT) No. 5835-1/17
LC75374E
SANYO: QIP44MA
CMOS IC

Related parts for lc75374e

lc75374e Summary of contents

Page 1

... Ordering number : EN5835 Electronic Volume and Tone Control for Car Stereos Overview The LC75374E is an electronic volume and tone control circuit that provides volume, balance, fader, bass and treble, super bass, input switching, and input and output level controls and requires a minimal number of external components to implement these functions ...

Page 2

... Output impedance R O [Bass and Treble Control Block] Bass control range Gbass Treble control range Gtre Output load resistance R L Output impedance R O LC75374E = Conditions V DD CL, DI, CE When Ta ≤ 85°C and mounted on a printed circuit board = Conditions V DD CL, DI, CE ...

Page 3

... Output at maximum attenuation Vo min Output noise voltage High-level input voltage I IH Low-level input voltage I IL Pin Assignment LC75374E = Conditions Max. Boost LSB2, RSB2 : kΩ kHz Vrms Vrms kHz, All controls flat overall Vrms kHz, All controls flat overall kΩ ...

Page 4

... Equivalent Circuit LC75374E No. 5835-4/17 ...

Page 5

... Control System Timing and Data Format Applications must input the stipulated serial data to the CE, CL, and DI pins to control the LC75374E. The data consists of a total of 52 bits, of which 8 bits are address and 44 bits are data. Address code Fader step control Bass control ...

Page 6

... Right channel super bass output and compensation capacitor connection 11 RSB2 22 LSIN • Super bass input 7 RSIN • These inputs must be driven by low-impedance circuits. 28 LTOUT • Tone control outputs 6 RTOUT LC75374E Description V ) used for the analog ground remove power SS Notes Continued on next page. No. 5835-6/17 ...

Page 7

... CE analog switches operate when this pin goes from high to low. Data transfers are enabled when this pin is high • Unused pins. These pins must be connected • Unused pins. These pins must be left open. LC75374E Description . SS Notes No. 5835-7/17 ...

Page 8

... Input Block Equivalent Circuit LC75374E The right channel is identical. No. 5835-8/17 ...

Page 9

... Main Volume Control Block Equivalent Circuit LC75374E Switch used for initial settings Switch used for initial settings To the tone control block The right channel is identical. No. 5835-9/17 ...

Page 10

... Tone Block Equivalent Circuit LC75374E From the main volume control block The right channel is identical. No. 5835-10/17 ...

Page 11

... Super Bass Block Equivalent Circuit LC75374E The right channel is identical. No. 5835-11/17 ...

Page 12

... Fader Volume Control Block Equivalent Circuit At the point that data corresponding to –∞ is transferred to the 1dB –step main volume control block, S1 and S2 will go to the open state. S3 and S4 will go to the on state at the same time. LC75374E Sample calculation Assume 64.5 kΩ, and ...

Page 13

... Applications must only send the actual initial data after this initialization data has been sent. • Applications must either cover the CL, DI, and CE lines with the ground pattern or use shielded cables for these lines to prevent the high-frequency digital signals that are transmitted over these lines from entering the analog signal system. LC75374E No. 5835-13/17 ...

Page 14

... Selector Fader Super volume + gain volume + tone bass control control control block block block block LC75374E Fader Volume Control Step Characteristics Overall Volume set level — dB Main Selector volume + gain + tone control control block block Output Gain Control Step Characteristics Overall Set level — ...

Page 15

... Supply voltage, V — Main Selector Super volume + gain + tone bass control control block block block LC75374E Total Harmonic Distortion - Input Level Characteristics position Selector + gain control block Total Harmonic Distortion - Supply Voltage Characteristics (2) Selector Fader + gain volume control control block ...

Page 16

... Bass Characteristics Frequency, f — Hz Main Selector volume + gain + tone control control block block LC75374E Selector Fader + gain volume control control block block Overall Main Fader Selector Super volume volume + gain bass + tone control ...

Page 17

... SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of November, 1998. Specifications and information herein are subject to change without notice. LC75374E PS No. 5835-17/17 ...

Related keywords