mh89760b Mitel, mh89760b Datasheet - Page 10

• Manufacturer Part Number: mh89760b
• Description: St-bus? Family T1/esf Framer & Interface
• Manufacturer: Mitel

MH89760B
Operating Status Information
Status Information regarding the operation of the
device is output serially via the Control ST-BUS
output (CSTo). The CSTo serial stream contains
Master Status Words 1 and 2, 24 Per Channel Status
Words, and a Phase Status Word. The Master Status
Words contain all of the information needed to
determine the state of the interface and how well it is
operating. The information provided includes frame
and super frame synchronization, slip, bipolar
violation counter, alarms, CRC error count, F
count, synchronization pattern mimic and a phase
status word. Tables 8 and 9 give a description of each
4-64
Bit
7-3
2-0
Bit
Bit
4-3
2-0
7
6
5
4
3
2
1
0
7
6
5
ChannelCnt
MFSYNC
CRCCNT
ESFYLW
BPVCnt
YLALR
Name
BitCnt
Name
Name
MIMIC
BlAlm
FrCnt
SLIP
ERR
BPV
SYN
XSt
pulse and the rising edge of E8Ko.
Bit Count. These three bits provide one bit resolution within the channel count described above.
Yellow Alarm Indication. This bit is set when the chip is receiving a 0 in bit position 2 of every
DS0 channel.
This bit is set if the frame search algorithm found more than one possible frame candidate when
it went into frame synchronization.
Terminal Framing Bit Error. The state of this bit changes every time the chip detects 4 errors in
the F
ESF Yellow Alarm. This bit is set when the device has observed a sequence of eight one’s and
eight 0’s in the FDL bit positions.
Multiframe Synchronization. This bit is cleared when D3/D4 multiframe synchronization has
been achieved. Applicable only in D3/D4 and SLC-96 modes of operation.
Bipolar Violation Count. The state of this bit changes every time the device counts 256 bipolar
violations.
Slip Indication. This bit changes state every time the elastic buffer in the device performs a
controlled slip.
Synchronization. This bit is set when the device has not achieved synchronization. The bit is
clear when the device has synchronized to the received DS1 data stream.
Blue Alarm. This bit is set if the receiver has detected two frames of 1’s and an out of frame
condition. It is reset by any 250 microsecond interval that contains a zero.
Frame Count. This is the ninth and most significant bit of the “Phase Status Word" (see Table
10). If the phase status word is incrementing, this bit will toggle when the phase reading exceeds
channel 31, bit 7. If the phase word is decrementing, then this bit will toggle when the reading
goes below channel 0, bit 0.
External Status. This bit reflects the state of the external status pin (XSt). The state of the XSt
pin is sampled once per frame.
Bipolar Violation Count. These two bits change state every 128 and every 64 bipolar violations,
respectively.
CRC Error Count. These three bits count received CRC errors. The counter will reset to zero
when it reaches terminal count. Valid only in ESF mode.
Channel Count. These five bits indicate the ST-BUS channel count between the ST-BUS frame
T
Table 8. Master Status Word 1 (Channel 15, CSTo)
Table 9. Master Status Word 2 (Channel 31, CSTo)
or FPS bit pattern. The bit will not change state more than once every 96ms.
Table 10. Phase Status Word (Channel 3, CSTo)
T
error
of the bits in Master Status Words 1 and 2, and Table
10 gives a description of the Phase Status Word.
In addition, the MH89760B has a Loss of Signal
(LOS) pin that is set High when 128 consecutive
ZEROs are received. While LOS is set High, RxA and
RxB are forced High. The LOS signal goes Low when
a ONEs density on 12.5% of the bits (equivalent to 48
bits) occurs in a two DS1 frame period.
Description
Description
Description
Preliminary Information
.