hbcr-2210 Avago Technologies, hbcr-2210 Datasheet
hbcr-2210
Related parts for hbcr-2210
hbcr-2210 Summary of contents
Page 1
... The bar code decoder ICs are compatible with most hand held scanners and some medium speed machine mounted laser heads. The HBCR-2210 series is compatible with fixed beam non- contact scanners, digital wands, and slot readers. In addition, the decoder is optimized for use with ...
Page 2
... This code can be scanned bi- directionally. Scanner Input The HBCR-2210 decode IC is designed to accept data from hand held digital scanners or slot readers with the following logic state: black = high, white = low. The same decode IC also accepts ...
Page 3
... The scanner type pin (SCT) on the HBCR-2210 series must be driven prior to power up or hard reset to identify the type of scanner connected. In the HBCR-2210 series ICs, the automatic laser shutoff feature delay time is adjustable as a con- figuration option ...
Page 4
... Notes: 1. Maximum power supply ripple of 100 mV peak to peak. 2. The HBCR-2210 series uses a 11.059 MHz crystal. For different crystal frequencies. multiply the specified baud rate and beeper frequencies by (crystal frequency/11.059 MHz) and multiply the element time interval ranges by (11.059 MHz/crystal frequency). ...
Page 5
... I Idle Mode Power CC Supply Current Note: 7. Applies only to HBCR-2210 and -2211 in Wand Mode or Laser Mode with Laser Idling enabled with no scanning or I/O operation in progress. Table 2. Summary of Features and Configurations - HBCR-2210 Series In the table below, the column entitled Selection is either: Software Escape Sequence and Optical Menu Programmability ...
Page 6
Feature Check Character For Code 39 Verification Enable For Interleaved When enabled, the check character at the end of the bar code data is verified by the decoder Check Character For both Code 39 and Interleaved Transmission ...
Page 7
Feature Function or Value Header Selection A string of characters pre- pended to the decoded message (10 characters, maximum) Trailer Selection A string of characters appended to the decoded message (10 characters, maximum) Reader Address Reader Address is transmitted at ...
Page 8
Feature Laser Connection When enabled, the scanner type Detection Enable pin is ignored at powerup. Instead, the decoder tests for a laser scanner to determine scanner type Laser Trigger When enabled, the laser scanner Latch Mode Enable continues to scan ...
Page 9
... For use with laser scanning, this command causes immediate execution of Command previous commands that would otherwise be postponed until the laser scan finishes Table 4. Summary of Other Features - HBCR-2210 Series Power Idle Mode Reduces current draw of processor from approximately wand mode when the wand is inactive ...
Page 10
Parallel Mode Handshake Timing Handshake and Data Lines CDY CRD PP0-PP7 Figure 1. Host Commands Received by Decode IC (Reader). Handshake Timing t = Falling edge of command ready to falling edge of command read. Max. ...
Page 11
... Figure 3. HBCR-2210 Serial Pinout. following baking cycles. The parts must then be mounted within 48 hours. If the parts are not mounted with hours, they must be re- baked. The total number of baking cycles must not exceed two. If the ICs ...
Page 12
... ECE/PT1 EIO/PT0 XTAL A10 XTAL Figure 5. HBCR-2210 Parallel Pinout. 4-58 PIN MNEMONICS AD0-AD7 ADDRESS/DATA BUS RxD RECEIVED DATA TxD TRANSMITTED DATA BR0-BR1 BAUD RATE PT0-PT1 PARITY 39 AD4 STB STOP BITS LSE LASER SCAN ENABLE 38 AD5 ...
Page 13
... Figure 6. HBCR-2211 Parallel Pinout. 52.8 51.9 40 INDEX MARK AREA 1 0.65 MAX. 2.54 ± 0.25 UNITS (mm) Figure 7. HBCR-2210 Mechanical Specifications. AD0-AD7 ADDRESS/DATA BUS DWR DATA WRITE HANDSHAKE DDY READY FOR DATA HANDSHAKE CRD COMMAND READ HANDSHAKE CDY COMMAND READY HANDSHAKE PT0-PT1 PARITY ...
Page 14
... INDEX MARK 1 17.4 16 4.57 4.20 0.53 0.33 16.0 15.0 UNITS (mm) Figure 8. HBCR-2211 Mechanical Specifications. (OPT) EE PROM HBCR-2210 SERIES BAR CODE ADDRESS/ INPUT DATA Figure 9. System Block Diagram. 4- 16.0 15.0 0.81 1.32 0.66 1. 0.51 MIN. CONTROL CONTROL ADDRESS RAM ADDRESS LATCH DATA 8 PARALLEL PORT (OPT) 646 OR (2)–74HC574 DATA SERIAL ...
Page 15
Warranty and Service The HP Bar Code Decode IC is warranted for a period of one year after purchase covering defects in material and workman- ship. Hewlett-Packard will repair or, at its option, replace products that prove to be defective ...