FS6370-01 American Microsystems, Inc., FS6370-01 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
FS6370-01
Manufacturer Part Number
FS6370-01
Description
EePROM Programmable 3-pll Clock Generator ic
Manufacturer
American Microsystems, Inc.
Datasheet
1.FS6370-01.pdf
(25 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FS6370-01
Manufacturer:
HIT
Quantity:
6 221
Part Number:
FS6370-01
Manufacturer:
AMIS
Quantity:
20 000
Company:
Part Number:
FS6370-01G-XTD
Manufacturer:
ON Semiconductor
Quantity:
38
FS6370-01
FS6370-01
FS6370-01
FS6370-01
EEPROM Programmable 3-PLL Clock Generator IC
EEPROM Programmable 3-PLL Clock Generator IC
EEPROM Programmable 3-PLL Clock Generator IC
EEPROM Programmable 3-PLL Clock Generator IC
8.2.2
Random write operations allow the master to directly
write to any register. To initiate a write procedure, the
R/W bit that is transmitted after the seven-bit device ad-
dress is a logic-low. This indicates to the addressed slave
device that a register address will follow after the slave
device acknowledges its device address. The register
address is written into the slave’s address pointer. Fol-
lowing an acknowledge by the slave, the master is al-
lowed to write eight bits of data into the addressed regis-
ter. A final acknowledge is returned by the device, and
the master generates a STOP condition.
If either a STOP or a repeated START condition occurs
during a Register Write, the data that has been trans-
ferred is ignored.
8.2.3
Random read operations allow the master to directly read
from any register. To perform a read procedure, the R/W
bit that is transmitted after the seven-bit address is a
logic-low, as in the Register Write procedure. This indi-
cates to the addressed slave device that a register ad-
dress will follow after the slave device acknowledges its
device address. The register address is then written into
the slave’s address pointer.
Following an acknowledge by the slave, the master gen-
erates a repeated START condition. The repeated
START terminates the write procedure, but not until after
the slave’s address pointer is set. The slave address is
then resent, with the R/W bit set this time to a logic-high,
indicating to the slave that data will be read. The slave
will acknowledge the device address, and then transmits
the eight-bit word. The master does not acknowledge the
transfer but does generate a STOP condition.
8.2.4
Sequential write operations allow the master to write to
each register in order. The register pointer is automati-
cally incremented after each write. This procedure is
more efficient than the Random Register Write if several
registers must be written.
Random Register Write Procedure
Random Register Read Procedure
Sequential Register Write Procedure
8
To initiate a write procedure, the R/W bit that is transmit-
ted after the seven-bit device address is a logic-low. This
indicates to the addressed slave device that a register
address will follow after the slave device acknowledges
its device address. The register address is written into the
slave’s address pointer. Following an acknowledge by the
slave, the master is allowed to write up to sixteen bytes of
data into the addressed register before the register ad-
dress pointer overflows back to the beginning address.
An acknowledge by the device between each byte of data
must occur before the next data byte is sent.
Registers are updated every time the device sends an
acknowledge to the host. The register update does not
wait for the STOP condition to occur. Registers are
therefore updated at different times during a Sequential
Register Write.
8.2.5
Sequential read operations allow the master to read from
each register in order. The register pointer is automati-
cally incremented by one after each read. This procedure
is more efficient than the Random Register Read if sev-
eral registers must be read.
To perform a read procedure, the R/W bit that is trans-
mitted after the seven-bit address is a logic-low, as in the
Register Write procedure. This indicates to the addressed
slave device that a register address will follow after the
slave device acknowledges its device address. The reg-
ister address is then written into the slave’s address
pointer.
Following an acknowledge by the slave, the master gen-
erates a repeated START condition. The repeated
START terminates the write procedure, but not until after
the slave’s address pointer is set. The slave address is
then resent, with the R/W bit set this time to a logic-high,
indicating to the slave that data will be read. The slave
will acknowledge the device address, and then transmits
all sixteen bytes of data starting with the initial addressed
register. The register address pointer will overflow if the
initial register address is larger than zero. After the last
byte of data, the master does not acknowledge the
transfer but does generate a STOP condition.
Sequential Register Read Procedure