BD4156MUV_09 ROHM [Rohm], BD4156MUV_09 Datasheet - Page 20

• Manufacturer Part Number: BD4156MUV_09
• Description: Power Switch for ExpressCardTM
• Manufacturer: ROHM [Rohm]

●USE NOTES
○
BD4156MUV
c
www.rohm.com
1.Absolute maximum ratings
2.Thermal design
3.Terminal-to-terminal short-circuit and mis-mounting
4.Operation in strong electromagnetic fields
5.Built-in thermal shutdown protection circuit
6.Capacitor across output and GND
7.Set substrate inspection
8.IC terminal input
2009 ROHM Co., Ltd. All rights reserved.
Although quality is rigorously controlled, the device may be destroyed when applied voltage, operating temperature, etc.
exceeds its absolute maximum rating. Because the source (short mode or open mode) cannot be identified once the IC is
destroyed, it is important to take physical safety measures such as fusing when implementing any special mode that
operates in excess of absolute rating limits.
Consider allowable loss (Pd) under actual operating conditions and provide sufficient margin in the thermal design.
When the mounting the IC to a printed circuit board, take utmost care to assure the position and orientation of the IC are
correct. In the event that the IC is mounted erroneously, it may be destroyed. The IC may also be destroyed when a
short-circuit is caused by foreign matter introduced into the clearance between outputs, or between an output and
power-GND.
Using the IC in strong electromagnetic fields may cause malfunctions. Exercise caution in respect to electromagnetic
fields.
This IC incorporates a thermal shutdown protection circuit (TSD circuit). The working temperature is 175°C (standard
value) with a -15°C (standard value) hysteresis width. When the IC chip temperature rises the TSD circuit is activated,
while the output terminal is brought to the OFF state. The built-in TSD circuit is intended exclusively to shut down the IC in
a thermal runaway event, and is not intended to protect the IC or guarantee performance in these conditions. Therefore,
do not operate the IC after with the expectation of continued use or subsequent operation once this circuit is activated.
When a large capacitor is connected across the output and GND, and the V3AUX_IN is short-circuited with 0V or GND for
any reason, current charged in the capacitor flows into the output and may destroy the IC. Therefore, use a capacitor
smaller than 1000 μF between the output and GND.
Connecting a low-impedance capacitor to a pin when running an inspection with a set substrate may produce stress on the
IC. Therefore, be certain to discharge electricity at each process of the operation. To prevent electrostatic accumulation
and discharge in the assembly process, thoroughly ground yourself and any equipment that could sustain ESD damage,
and continue observing ESD-prevention procedures in all handling, transfer and storage operations. Before attempting to
connect the set substrate to the test setup, make certain that the power supply is OFF. Likewise, be sure the power supply
is OFF before removing the substrate from the test setup.
This integrated circuit is a monolithic IC, with P substrate and P
The P layer and N layer of each element form a, PN junction. When the potential relation is GND>terminal A>terminal B,
the PN junction works as a diode, and when terminal B>GND terminal A, the PN junction operates as a parasitic transistor.
Parasitic elements inevitably form, due to the nature of the IC construction. The operation of the parasitic element gives
rise to mutual interference between circuits and results in malfunction, and eventually, breakdown. Consequently, take
utmost care not to use the IC in a way that would cause the parasitic element to actively operate, such as applying voltage
lower than GND (P substrate) to the input terminal.
Parasitic element
Pin A
N
P
+
N
GND
P
P substrate
P
+
N
Resistor
Pin A
Parasitic
element
Parasitic element
20/23
Pin B
N
P
+
+
isolation between elements.
C
B
N
E
GND
P
P substrate
Transistor (NPN)
P
+
N
GND
Other adjacent elements
Pin B
B
Technical Note
2009.05 - Rev.A
C
E
GND
Parasitic
element