LTC2634-HMI10 LINER [Linear Technology], LTC2634-HMI10 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
LTC2634-HMI10
Manufacturer Part Number
LTC2634-HMI10
Description
Manufacturer
LINER [Linear Technology]
Datasheet
1.LTC2634-HMI10.pdf
(30 pages)
LTC2634
ELECTRICAL CHARACTERISTICS
temperature range, otherwise specifi cations are at T
LTC2634-HMI12/-HMI10/-HMI8/-HMX12/-HMX10/-HMX8/-HZ12/-HZ10/-HZ8 (V
SYMBOL
t
t
t
t
t
t
t
t
t
t
t
t
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltages are with respect to GND.
Note 3: High temperatures degrade operating lifetimes. Operating lifetime
is derated at temperatures greater than 105°C.
Note 4: Linearity and monotonicity are defi ned from code k
2
rounded to the nearest whole code. For V
and linearity is defi ned from code 26 to code 4,095. For V
N = 12, k
Note 5: Inferred from measurement at code 16 (LTC2634-12), code 4
(LTC2634-10) or code 1 (LTC2634-8), and at full-scale.
10
1
2
3
4
5
6
7
8
9
10
11
12
N
– 1, where N is the resolution and k
L
= 16 and linearity is defi ned from code 16 to code 4,095.
PARAMETER
SDI Valid to SCK Setup
SDI Valid to SCK Hold
SCK High Time
SCK Low Time
CS/LD Pulse Width
LSB SCK High to CS/LD High
CS/LD Low to SCK High
CLR Pulse Width
LDAC Pulse Width
CS/LD High to SCK Positive Edge
SCK Frequency
CS/LD High to LDAC High or Low Transition
SDO Propagation Delay from SCK Falling Edge
L
is given by k
FS
= 2.5V and N = 12, k
L
= 0.016 • (2
FS
L
A
= 4.096V and
to code
= 25°C. V
CONDITIONS
50% Duty Cycle
C
LOAD
V
L
CC
= 26
N
/ V
The
= 4.5V to 5.5V
= 10pF
FS
),
l
CC
denotes the specifi cations which apply over the full operating
= 4.5V to 5.5V, V
Note 6: This IC includes current limiting that is intended to protect the
device during momentary overload conditions. Junction temperature can
exceed the rated maximum during current limiting. Continuous operation
above the specifi ed maximum operating junction temperature may impair
device reliability.
Note 7: Digital inputs at 0V or V
Note 8: Guaranteed by design and not production tested.
Note 9: Internal Reference mode. DAC is stepped 1/4 scale to 3/4 scale
and 3/4 scale to 1/4 scale. Load is 2kΩ in parallel with 100pF to GND.
Note 10: Temperature coeffi cient is calculated by dividing the maximum
change in output voltage by the specifi ed temperature range.
FS
= 4.096V)
OUT
unloaded unless otherwise specifi ed.
l
l
l
l
l
l
l
l
l
l
l
l
l
CC
MIN
200
10
20
15
4
4
9
9
7
7
7
.
TYP
MAX
50
20
UNITS
2634fb
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns