LTC3528 LINER [Linear Technology], LTC3528 Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
LTC3528
Manufacturer Part Number
LTC3528
Description
Manufacturer
LINER [Linear Technology]
Datasheet
1.LTC3528.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC3528BEDDB
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC3528BEDDB#PBF
Manufacturer:
TI
Quantity:
122
Part Number:
LTC3528BEDDB#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC3528BEDDB-2#PBF
Manufacturer:
LT
Quantity:
1 628
Part Number:
LTC3528BEDDB-2#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3528BEDDB-2#TRMPBF
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LTC3528BEDDB-2#TRPBF
Manufacturer:
LT
Quantity:
20 000
Company:
Part Number:
LTC3528EDDB
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3528EDDB
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC3528EDDB#TRMPBF
Manufacturer:
LTC
Quantity:
169
APPLICATIONS INFORMATION
The inductor current ripple is typically set for 20% to
40% of the maximum inductor current. High frequency
ferrite core inductor materials reduce frequency depen-
dent power losses compared to cheaper powdered iron
types, improving effi ciency. The inductor should have low
ESR (series resistance of the windings) to reduce the I
power losses, and must be able to handle the peak induc-
tor current without saturating. Molded chokes and some
chip inductors usually do not have enough core area to
support the peak inductor currents of 1.5A seen on the
LTC3528/LTC3528B. To minimize radiated noise, use a
shielded inductor. See Table 1 for suggested components
and suppliers.
Table 1. Recommended Inductors
VENDOR
Coilcraft
(847) 639-6400
www.coilcraft.com
Coiltronics
Sumida
(847) 956-0666
www.sumida.com
TDK
Toko
(408) 432-8282
www.tokoam.com
Wurth
(201) 785-8800
www.we-online.com
Output and Input Capacitor Selection
Low ESR (equivalent series resistance) capacitors should
be used to minimize the output voltage ripple. Multilayer
ceramic capacitors are an excellent choice as they have
PART/STYLE
LPO2506, MSS5131
MSS6122, MOS6020
ME3220, DO1608C
1812PS
SD14, SD18, SD20
SD25, SD52
CD43
CDC5D23B
CDRH5D18
CR43
VLP , VLF
VLCF , SLF
D53, D63
D73, D75
WE-TPC type M, MH
2
R
extremely low ESR and are available in small footprints.
A 10μF to 22μF output capacitor is suffi cient for most ap-
plications. Values larger than 22μF may be used to obtain
extremely low output voltage ripple and improve transient
response. X5R and X7R dielectric materials are preferred
for their ability to maintain capacitance over wide voltage
and temperature ranges. Y5V types should not be used.
The internal loop compensation of the LTC3528/LTC3528B
is designed to be stable with output capacitor values of 10μF
or greater. Although ceramic capacitors are recommended,
low ESR tantalum capacitors may be used as well.
A small ceramic capacitor in parallel with a larger tantalum
capacitor may be used in demanding applications which
have large load transients. Another method of improving
the transient response is to add a small feed-forward
capacitor across the top resistor of the feedback divider
(from V
suffi ce.
Low ESR input capacitors reduce input switching noise
and reduce the peak current drawn from the battery. It
follows that ceramic capacitors are also a good choice
for input decoupling and should be located as close as
possible to the device. A 10μF input capacitor is suffi cient
for most applications. Larger values may be used without
limitations. Table 2 shows a list of several ceramic capaci-
tor manufacturers. Consult the manufacturers directly for
detailed information on their selection of ceramic parts.
Table 2. Capacitor Vendor Information
SUPPLIER
AVX
Murata
Taiyo-Yuden
TDK
OUT
to FB). A typical value of 33pF will generally
PHONE
(803) 448-9411
(714) 852-2001
(408) 573-4150
(847) 803-6100
LTC3528/LTC3528B
WEBSITE
www.avxcorp.com
www.murata.com
www.t-yuden.com
www.component.tdk.com
11
3528fa