LTC3605 LINER [Linear Technology], LTC3605 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
LTC3605
Manufacturer Part Number
LTC3605
Description
20V, 5A Synchronous Step-Down Regulator
Manufacturer
LINER [Linear Technology]
Datasheet
1.LTC3605.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC3605AEUF
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3605AEUF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3605AEUF#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC3605AIUF
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3605AIUF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC3605AIUF#PBF
Manufacturer:
LT
Quantity:
3 100
Company:
Part Number:
LTC3605AIUF#TRPBF
Manufacturer:
LT
Quantity:
3 100
Company:
Part Number:
LTC3605EDE
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3605EDE
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3605EUF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
OPERATION
Output Voltage Programming
The output voltage is set by an external resistive divider
according to the following equation:
The resistive divider allows the V
of the output voltage as shown in Figure 1.
Programming Switching Frequency
Connecting a resistor from the RT pin to SGND programs
the switching frequency from 800kHz to 4MHz according
to the following formula:
The internal PLL has a synchronization range of ±30%
around its programmed frequency. Therefore, during
external clock synchronization be sure that the external
clock frequency is within this ±30% range of the RT pro-
grammed frequency.
Output Voltage Tracking and Soft-Start
The LTC3605A allows the user to program its output voltage
ramp rate by means of the TRACK/SS pin. An internal 2µA
pulls up the TRACK/SS pin to INTV
capacitor on TRACK/SS enables soft starting the output
to prevent current surge on the input supply. For output
tracking applications, TRACK/SS can be externally driven
by another voltage source. From 0V to 0.6V, the TRACK/SS
voltage will override the internal 0.6V reference input to the
error amplifier, thus regulating the feedback voltage to that
of TRACK/SS pins. During this start-up time, the LTC3605A
will operate in discontinuous mode. When TRACK/SS is
above 0.6V, tracking is disabled and the feedback voltage
will regulate to the internal reference voltage.
V
Frequency (Hz) =
OUT
= 0.6V • (1 + R2/R1)
Figure 1. Setting the Output Voltage
LTC3605A
R
1.6e11
SGND
T
FB
(W)
V
OUT
FB
R2
R1
3605A F01
CC
pin to sense a fraction
. Putting an external
C
FF
Output Power Good
When the LTC3605A’s output voltage is within the ±10%
window of the regulation point, which is reflected back as
a V
voltage is good and the PGOOD pin is pulled high with an
external resistor. Otherwise, an internal open-drain pull-
down device (12Ω) will pull the PGOOD pin low. To prevent
unwanted PGOOD glitches during transients or dynamic
V
a blanking delay of approximately 52 switching cycles.
Multiphase Operation
For output loads that demand more than 5A of current,
multiple LTC3605As can be cascaded to run out of phase
to provide more output current. The CLKIN pin allows the
LTC3605A to synchronize to an external clock (±30% of
frequency programmed by RT) and the internal phase-
locked-loop allows the LTC3605A to lock onto CLKIN’s
phase as well. The CLKOUT signal can be connected to the
CLKIN pin of the following LTC3605A stage to line up both
the frequency and the phase of the entire system. Tying
the PHMODE pin to INTV
a phase difference (between CLKIN and CLKOUT) of 180
degrees, 120 degrees, or 90 degrees respectively, which
corresponds to 2-phase, 3-phase or 4-phase operation. A
total of 12 phases can be cascaded to run simultaneously
out of phase with respect to each other by programming
the PHMODE pin of each LTC3605A to different levels.
Internal/External ITH Compensation
During single phase operation, the user can simplify
the loop compensation by tying the I
enable internal compensation. This connects an internal
30k resistor in series with a 40pF capacitor to the output
of the error amplifier (internal ITH compensation point)
while also activating output voltage positioning such
that the output voltage will be 1.5% above regulation at
no load and 1.5% below regulation at full load. This is a
trade-off for simplicity instead of OPTI-LOOP
tion, where ITH components are external and are selected
to optimize the loop transient response with minimum
output capacitance.
OUT
FB
changes, the LTC3605A’s PGOOD falling edge includes
voltage in the range of 0.54V to 0.66V, the output
CC
, SGND or INTV
LTC3605A
TH
pin to INTV
CC
/2 generates
®
optimiza-
CC
3605af
9
to