CY7C68033 CYPRESS [Cypress Semiconductor], CY7C68033 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
CY7C68033
Manufacturer Part Number
CY7C68033
Description
Manufacturer
CYPRESS [Cypress Semiconductor]
Datasheet
1.CY7C68033.pdf
(33 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY7C68033-56BAXC
Manufacturer:
Cypress Semiconductor Corp
Quantity:
10 000
Company:
Part Number:
CY7C68033-56LTXC
Manufacturer:
Cypress
Quantity:
270
Document #: 001-04247 Rev. *D
Table 8. NX2LP-Flex Pin Descriptions
Note
6. Unused inputs should not be left floating. Tie either HIGH or LOW as appropriate. Outputs should only be pulled up or down to ensure signals at power-up and in
Number
56 QFN
Pin
standby. Note also that no pins should be driven while the device is powered down.
42
54
29
30
31
9
8
5
4
1
2
Default Pin
DMINUS
DPLUS
RESET#
XTALIN
XTALOUT
GPIO9
RDY0 or
SLRD
RDY1 or
SLWR
CTL0 or
FLAGA
CTL1 or
FLAGB
CTL2 or
FLAGC
Name
Firmware
GPIO9
R_B1#
R_B2#
NAND
Usage
RE0#
RE1#
WE#
N/A
N/A
N/A
N/A
N/A
[6]
Output
Type
I/O/Z
I/O/Z
Input
Input
Input
Input
O/Z
O/Z
O/Z
O/Z
Pin
12 MHz GPIO9 is a bidirectional IO port pin.
Default
State
N/A
N/A
N/A
N/A
N/A
H
H
H
Z
Z
USB D– Signal. Connect to the USB D– signal.
USB D+ Signal. Connect to the USB D+ signal.
Active LOW Reset. Resets the entire chip. See section ”Reset and
Wakeup” on page 7 for more details.
Crystal Input. Connect this signal to a 24-MHz parallel-resonant,
fundamental mode crystal and load capacitor to GND.
It is also correct to drive XTALIN with an external 24-MHz square
wave derived from another clock source. When driving from an
external source, the driving signal should be a 3.3V square wave.
Crystal Output. Connect this signal to a 24-MHz parallel-resonant,
fundamental mode crystal and load capacitor to GND.
If an external clock is used to drive XTALIN, leave this pin open.
Multiplexed pin whose function is selected by IFCONFIG[1:0].
RDY0 is a GPIF input signal.
SLRD is the input-only read strobe with programmable polarity
(FIFOPINPOLAR[3]) for the slave FIFOs connected to FD[7:0] or
FD[15:0].
R_B1# is a NAND Ready/Busy input signal.
Multiplexed pin whose function is selected by IFCONFIG[1:0].
RDY1 is a GPIF input signal.
SLWR is the input-only write strobe with programmable polarity
(FIFOPINPOLAR[2]) for the slave FIFOs connected to FD[7:0] or
FD[15:0].
R_B2# is a NAND Ready/Busy input signal.
Multiplexed pin whose function is selected by IFCONFIG[1:0].
CTL0 is a GPIF control output.
FLAGA is a programmable slave-FIFO output status flag signal.
Defaults to programmable for the FIFO selected by the
FIFOADR[1:0] pins.
WE# is the NAND write enable output signal.
Multiplexed pin whose function is selected by IFCONFIG[1:0].
CTL1 is a GPIF control output.
FLAGB is a programmable slave-FIFO output status flag signal.
Defaults to FULL for the FIFO selected by the FIFOADR[1:0] pins.
RE0# is a NAND read enable output signal.
Multiplexed pin whose function is selected by IFCONFIG[1:0].
CTL2 is a GPIF control output.
FLAGC is a programmable slave-FIFO output status flag signal.
Defaults to EMPTY for the FIFO selected by the FIFOADR[1:0] pins.
RE1# is a NAND read enable output signal.
CY7C68033/CY7C68034
Description
Page 14 of 33
[+] Feedback
[+] Feedback